Polycom VSX 6000 (220022222001) Video Conference - Answered Questions & Fixed issues

Try changing the wire. Must be the 30 foot cable not the 10 foot which is specifically the daisy chain ... The former 30 foot is the specific cable from codec to mic. If changing this fails and you tested the mic, then your unit is either suffering corrupted software or the mic hardware is damaged. David

Your VSX 6000 does not support Multipoint. YOu will have to move up to the VSX 7000 or 8000. The VSX 7000 supports MP and the VSX 8000 supports 6 site mp if you have that option installed. DAVID

Try using the S-Video output and then try using the VGA output from the VSX 6000 unit. The unit can be fixed to output from either as the first monitor output (you may have the dual monitor option enabled). If this does not work the resolution of the TV might be HD, the output of your VSX 6000 is Standard Definition. You will need a monitor that accepts standard definition. If this does not work, I would reboot your VSX 6000 and try again. David

you can contact the mobile service provider.......

it is not able to resolve the IP address for the time server. I am having the same problem. If you enter in the IP address for the time server it will resolve your problem

Constant red means it is set and ready to record messages after x amount of rings. Flashing red means you have a message. Please always include the model number is such questions and I can find you a manual. Polycom has lots! https://www.google.com/search?q=Polycom+phone+manual ..

try this on the manual: https://www.google.it/url?sa=t&rct=j&q=&esrc=s&source=web&cd=3&cad=rja&uact=8&ved=0CC4QFjAC&url=http%3A%2F%2Fsupport.polycom.com%2Fglobal%2Fdocuments%2Fsupport%2Fsetup_maintenance%2Fproducts%2Fvoice%2Fvortex_ef2280_programming_guide.pdf&ei=Z_j_VNXZH4vlaqq-gdAH&usg=AFQjCNGMJQMh4hSijpy9ic619NkkmlKOPA&bvm=bv.87611401,d.d2s

are you sure this feature is not blocked on your line? check with another phone connected to the same socket if you can dial the same numbers

hello This is not a dialing but trying to connect to the IP address setup in the system. Start editing the IP address giving the one that you would have already allocated to the device in the Router (i.e. 192.168.1.99) and then reboot it. It should connect then automatically. Best regards

The easiest way to fix this is to have use TFTPD32 and set the firmware in the default directory so that when the phone boots it gets its DHCP with Option 66 from the machine running TFTPD32 and automatically pulls the firmware

Unless you are good a solder then you probably won't be able to do it. You wolud need to solder a potentiometer inline of the + voltage to the speaker. Or solder one inline with the existing one. Potentiometer = voltage control aka volume control.

HI. sorry to hear that. Well, here's the solution
Settings should be changed, if it did not resolved the issue? check your coverage area and lastly go and seek a technician to have your device check and re evaluate the condition the mouthpiece or earpiece needs to be replace.
Please accept my solution..thanks

You power supply is probably defective

Has this been fixed yet?

http://www.brennanit.com.au/UserGuides/User%20Guide%20-%20Polycom%20Soundstation2.pdf

google speakerphone 210 manual for choices.

Question edited for clarity. Question moved from Video Consoles category. Trying to find a manual. Are you sure that model is correct? Eircom should give you a manual PDF. https://www.google.com/search?q=Eircom+perform+100+manual and https://www.google.com/search?q=Eircom+perform+100 ..

Good question but no 'make model (what it is). Base units have an antenna, make sure it is extended. Make sure the batteries in the satellite hand sets are good as they send out the signal to the base unit to be 'in range'. Not sure about the PIN request, refer to the manual. They are all online. Google make model manual ..

NiMH voltage : 1.2 V capacity : 750 mAh

1. First, try resetting your phone by powering it off completely and then turning it back on after a few seconds. This can sometimes resolve minor software glitches.
2. If the problem persists, you can try contacting your mobile service provider and ask them to reset your voicemail on their end. They might be able to resolve the issue from their system.
3. Another option is to manually check your voicemail and listen to any existing messages. Sometimes, even if you've listened to a message, the indicator might stay on. By checking your voicemail and ensuring there are no unread messages, it might help clear the indicator.

If none of these steps work, it could be a more complex issue that might require technical support from Sonim or your mobile service provider. They should be able to provide further assistance. Let me know if there's anything else I can help with!