Top 20 Venta Airwasher VS370 2 Gallon Humidifier Questions & Answers

You have a cool mist humidifier there is no steam. Please read manual or look up unit on internet

My Guess is that the reletive humidity in the room is not low enough to see any vapors coming from the machine. Normaly you won't see these anyway. Some models in the stores seem to make more mist than what you get at home. If the humididty level in a room is close to what is coming out of the machine there will be no signs of any mist coming out. Just make sure the filters are clean and check and make sure the water level is going down on the machine and this will tell you its workin. the faster you are using the water in the tank the more you are putting in the air! If this is a hot mist machine then I would say the heating element in the machine is not working.

From the quick research that I did I'm finding 100 hours. That will vary very significantly depending on the mineral content (hardness) of your water. If you have alot of mineral in your water the filter may have to be changed much more often to maintain good operation of the unit.

This has happened to me. Check the contact points in the base of the machine. Ours had some corrosion on them. I took an emery board and filed the corrosion off to clean the contact points.

Filters need to be changed regularly depending on environment may have to change more often.

These systems can be very troublesome. It is possible that you are having mineral buildup in your system from the water supply. You can try adding 1/4 cup vinegar to your water to help clean away deposits. See if that helps .

Every 10-14 days, the lower housing should be wiped out with a damp sponge. The disk stacks should be rinsed off and/or brushed off with a brush or sponge. Periodically, the Venta Cleaner can be used for a thorough cleaning. At all times, care should be taken to keep water away from the motor.

venta-usa.com is your best bet to solving the problem.

As awkward as it sounds tap water is bad for the unit, Try buying store bought water. If this does not help you will need to change the filter in the system also you can set the desired humidity level to 60% so it will keep pumping if you still have an issue with the product refer to your manufacture. Good Luck

Hi there,

Well If there's no air movement out the front or back of the unit, the fan motor may be burned out or stuck, or the fan blade may be broken. If so, you need to replace the fan motor or the fan blade.
The tank may be full. Your dehumidifier has a safety device that turns off the dehumidifier when the water tank is full. Usually the tank itself either presses against a switch or there's a device connected to the tank that triggers a switch when the tank is in place and full.
If you've emptied the tank and the unit doesn't run, inspect the place where the tank rests to see if there's a switch or mechanism that's not being activated. You may be able to turn it on with a simple flick of your finger.

Good Luck!!

Thanks

Question edited for clarity. Parts suppliers and a link to the maker. https://www.google.com/search?q=sunbeam+scm3755c+tank ..

Without brand and model, my advice is definitely a shot in the dark. Only your manual or your manufacturer's site can inform you of what the flashing means. Here are some tips that might help you increase the humidity in your room: Check the humidifier's water level: Make sure that the humidifier has enough water to function properly. If the water level is low, the humidifier may not be able to produce enough moisture to increase the humidity in the room. Clean the humidifier: Over time, mineral deposits and bacteria can build up in the humidifier, which can affect its performance. Clean the humidifier regularly according to the manufacturer's instructions. Place the humidifier in the right location: Place the humidifier in a central location in the room, away from walls and other obstructions. This will help the humidifier distribute moisture evenly throughout the room. Use a humidistat: A humidistat is a device that measures the humidity in the room and automatically adjusts the humidifier's output to maintain a desired humidity level. If your humidifier does not have a built-in humidistat, you can purchase a separate one and use it to control the humidity level in the room.

There could be several reasons why a humidifier stops running after refilling it with water. One of the most common reasons is that the humidifier's float switch is stuck in the "low water" position, which prevents the humidifier from turning on even after refilling it with water . Another reason could be that the humidifier's water level sensor is malfunctioning, which causes the humidifier to stop running even when there is enough water in the tank/ If you have a whole-house humidifier, it could be that the humidistat is set too low, which causes the humidifier to turn off even when there is enough water in the tank 1. Alternatively, if you have a portable humidifier, it could be that the unit's motor has burned out or that its fan has stopped working . To troubleshoot this issue, you can try cleaning the float switch or replacing the water level sensor if they are damaged. If you have a whole-house humidifier, you can try adjusting the humidistat to a higher setting. If you have a portable humidifier, you can try replacing its motor or fan

There could be several reasons why a humidifier stops running after refilling it with water. One of the most common reasons is that the humidifier's float switch is stuck in the "low water" position, which prevents the humidifier from turning on even after refilling it with water . Another reason could be that the humidifier's water level sensor is malfunctioning, which causes the humidifier to stop running even when there is enough water in the tank/ If you have a whole-house humidifier, it could be that the humidistat is set too low, which causes the humidifier to turn off even when there is enough water in the tank 1. Alternatively, if you have a portable humidifier, it could be that the unit's motor has burned out or that its fan has stopped working . To troubleshoot this issue, you can try cleaning the float switch or replacing the water level sensor if they are damaged. If you have a whole-house humidifier, you can try adjusting the humidistat to a higher setting. If you have a portable humidifier, you can try replacing its motor or fan

this forum does not sell parts. call manufacturer of goggle you make and model number +parts.

All question need full 'make model (what it is)' to answer efficiently. Some actually spay a mist of water, but the better one suck dry air in and blow moister air out through the saturated filter membrane. The ones that spray water mist damage furniture and anything near it. If it is the spray type, it needs descaling. You could Google make model manual Or list it under her by clicking Comment under _my_ answer. .

Question edited for clarity. Claim on the warranty irrespective of how long you have had it. https://www.google.com/search?q=safety+1st+ultrasonic+humidifier+model+number+IH446+warranty ..

Sure, here's the user manual for the Panasonic air purifier with humidifier F-VXT70: Introduction: Thank you for purchasing the Panasonic air purifier with humidifier F-VXT70. This unit combines a powerful air purifying function with a high-performance humidifying function to provide you with clean and comfortable air. Safety precautions: Please read and follow all safety precautions before using this product.

• This product is for indoor use only.
• Do not use this product for any purpose other than its intended use.
• Do not disassemble or modify this product.
• Keep this product out of reach of children and pets.
• Unplug this product before cleaning or maintaining it.
• Do not use this product near water.
• Do not use this product with a damaged power cord.
• Do not use this product if it has been dropped or damaged.
• Use only the power cord provided with this product.

Operating instructions:

1. Place the unit in a stable location near a power outlet.
2. Open the water tank cover and fill the tank with clean water up to the MAX line.
3. Close the water tank cover and plug in the power cord.
4. Press the power button to turn on the unit. The air purifying and humidifying functions will start automatically.
5. Use the mode button to select the desired mode:

• Auto mode: The unit will automatically adjust its operation based on the air quality and humidity level.
• Manual mode: You can adjust the fan speed and humidity level manually.

1. Use the fan speed button to adjust the fan speed in manual mode.
2. Use the humidity level button to adjust the humidity level in manual mode.
3. When the water in the tank runs out, the unit will automatically stop the humidifying function. You can refill the tank and resume operation by pressing the power button again.
4. Clean the unit regularly according to the maintenance instructions in the user manual.

Maintenance instructions:

1. Unplug the power cord and empty the water tank before cleaning the unit.
2. Use a soft cloth to wipe the exterior of the unit.
3. Remove the filter and wash it with water. Allow it to dry completely before reinstalling it.
4. Clean the water tank with a soft brush and mild detergent. Rinse thoroughly and allow it to dry completely before refilling it.
5. Clean the humidifying unit with a soft brush and mild detergent. Rinse thoroughly and allow it to dry completely before reinstalling it.
6. Reassemble the unit and plug in the power cord.

Troubleshooting: If the unit does not operate properly, try the following solutions:

• Make sure the power cord is securely plugged into the power outlet.
• Check the water tank and refill it if necessary.
• Clean the filter, water tank, and humidifying unit according to the maintenance instructions.
• Contact the customer service center if the problem persists.

From what you've described, it seems that the "A" setting may be a special or additional mode of operation. It could be an "Auto" or "Adaptive" setting that adjusts the fan speed based on the humidity level in the room, or it could be a specific function designed for a certain type of room. I recommend checking the owner's manual or contacting the manufacturer directly to find out more information about the specific function of the "A" setting on your Aircare (Valiant) Humidifier HD1409.

Hi, please switch power outlets before attempting to power the humidifier again. Please double check that you've filled the humidifier as instructed and chosen the lowest setting at first to start. If the issue persists and the device is more than a few years old, you can request repair or replacement assistance from qvc next to help overcome this issue. Thank you.