Alesis Sr 16 Stereo Drum Machine - Answered Questions & Fixed issues

Hello has you for repair this orgel ? i have th? same probl?me

I replaced the internal battery and since I couldn't find a battery holder, I added 3 wire posts to the board, so next time I won't have to remove the whole board, simply unsolder from above. Simple hack.

Assuming you've tried rebooting the white screen one? If so, You need to take both to a qualified repair man and get the job done right. If you start swapping parts without knowing what works and what doesn't, you risk screwing up the good parts,

Re-initalize the machine. If that doesn't work, it's time to take it to the shop. However, replaceing it may be more cost effective.

In my case, a -15 volt trace runs under the 1/4 inch connectors and right at the edge of the circuit board. I think slight movement of the connector wears that trace out and in my case it caused it to short to a nearby trace. I ran a 30 guage wire in its place to fix it. Also see https://www.youtube.com/watch?v=6RJVtQ8i0eY

According to the Alesis SR16 Frequently Asked Question section: Power On while holding down Erase and Play. http://alesis.com/sr16

It sounds like your buttons are stuck...I would take it back for an exchange...good luck

You might try going to this webpage https://www.alesis.com/sr16 and from the docs&downloads section download and search the Reference manual. It's also here http://www.burnkit2600.com/manuals/ALESIS_SR-16_OM.pdf (this looks more like a user guide though) Failing that, choose 'support' from the th top of the page and either contact Alesis support or else ask your question in the 'community' (which you will have to join). Another community which deems to have an interest in the SR-16 is www.circuitbenders.co.uk but I think it unlikely that they could direct you to a circuit diagram, though it is slight possibility that someone might know the value of the capacitor C5 23.December.2014

2200mfd / 16volt Make sure there are no other problems before you replace it! It does not get barbequed by itself. Have Fun.

Really Quick. Two problems are unrelated. Assume older unit. Needs memory battery, and new display.

Try cleaning your volume potentiomenter with contact cleaner (they come in spray can's), the scratchy sound is audible when you turn your volume control on, the contacts inside your potentiometer accumulated dust or some other particles.

5.4J Copy a Song to Another SR-16 Via MIDI The SR-16 can send Song system exclusive information to another SR-16 via MIDI. If you have only one SR-16, you can skip this section. 1. The source SR-16 should be in Song mode and stopped. Connect the source SR-16 MIDI out to the destination SR-16 MIDI in. 2. Select the Song to be copied. 3. Press and hold the COPY button, and keep holding it down until step (5). The display says COPY TO SONG. 4. Do not enter any destination Song number-just press PLAY to send the data out over MIDI. It will end up in whatever Song number had been selected at the receiver. If the Song was not empty, the new Song steps will be appended to the existing Song steps. 5. Release the COPY and PLAY buttons. Caution: This does not transfer Pattern information, only the song steps. To transfer Patterns to another SR-16, see section 3.3D and 3.3E. Hopefully this helps, it comes out of the SR16 Manual, page 40 I think Cheers Pete

I got a service manual but don't know how to get it to you. I can sent it by email. Let me hear from you. Contact: [email protected] (subject: "Manual") The manual is for Alesis HR-16B SRV comes in PDF format.

http://www.burnkit2600.com/manuals/ALESIS_SR-16_OM.pdf Try that

go to the ballad #4 setting you will find a 3/4 beat in a 12 beat time. This is a preset pattern

yes, it should light up when you turn it on. Make sure you have the right adaptor. The voltage & polarity will be wreitten on the unit. My adaptor is from Alesis. You can find these on ebay.

I'm delighted for you and wish you every happiness If this is the answer great, if not what's your question? Windows Start button, run type msconfig in the run window, click the startup tab, look fo launcher pro and uncheck it. Shoes?

Audacity is an audio editor that will allow you to do that. It's a free download

These of course have to be connected to an external amplifier and speaker.

Check that your amp is working first.

Open the box and try to spray a cleaning/lubricating solution inside the volume pot mechanism like Deoxit D5, you can also spray a little of it on the output connectors where you plugin your cable that runs to the amp. If that doesn't solve your problem you have to replace the volume potentiometer. The machine I have had similar issues and I was lucky to have a pot close in size and resistance value as the original which in my case was broken, so I just replaced it. Good luck!