Mitsubishi WD-73735 Television - Answered Questions & Fixed issues

I would first suggest checking where lamp plugs into the two pins that the replacement lamp went in correctly----it is not uncommon for it to push the contacts away (not engage correctly) and you will be able to see this with the lamp removed---red should be lamp light failure and most of these have a self check button sequence based on actual model number.

The main power supply regulator section circuit fault. Either it will be a separate board, or the part of main board. Check and replace damaged component/s at its main power regulator [SMPS] section circuit. Contact any service technician. If you wish to get some details; check the site linked here. Pull up older posts. http://electro-medical.blogspot.com/ http://electronicshelponline.blogspot.com/

If you wish to get some details; check the site linked here. Pull up older posts. http://electronicshelponline.blogspot.com/

if you have no lights come on the front of TV, you definitely have a power supply issue. Don't know what previous servicer did, but I would be looking at ALL wires & connectors.

http://www.fixya.com/answer/answerpageslideview.aspx?ctg=104&fml=0&brd=0&thid=21593400 hear the part list for your mis dlp..just make shour it the right one plz befor you git the parts you need

no buy a blue ray player with hdmi cable!

No. It is only available by authorized service center. Texas Instruments do not sell it by open market.

the dlp chip needs replacement the dots will keep mltiplying untill the entire screen is filled.

i replaced my bulb a mouth ago and now the red light is on and theres no sound or picture but the bulb doesnt look blown or bad wut could it be

This is called the blinking light of death in these sets---when power is removed from set and put back the light should blink for about 70 seconds and stop----it is the digital signal unit booting up.About the only common easy failure for this is there are 4 caps on the power supply board that fail---they will be puffed up on top like photo attached.

tried with replacing first bulging electrolytic capacitors at the power supply board. you can find parts at www.digikey.com a panasonic brand of capacitors with low esr 105c FC or FM series much better replacement just make sure same rating.

If your TV has a picture but no sound, start by checking the obvious such as whether the mute button is on or whether the volume has been turned all the way down. Next check your cable connections and make sure everything is plugged in tightly. Change channels to make sure that it's not a technical difficulty with your TV service provider or TV station. Call your service provider to see if they're experiencing issues with their audio.Try reconnecting the HDMI cable after you turn off the TV.Make sure your remote is on the correct input, and see if you have sound while playing a DVD or video game.For a simple troubleshooting checklist, see No sound on TV and get more details on some simple fixes for this problem. I hope this helps!

ok consider this one removed.

Issue is a damaged Optical light engine in the model indicated---

Hello, welcome to Fixya!My question would be; how long have you been using the TV and have you every changed the lamp?If you have never changed the lamp or if it has been a long time since you changed the lamp, then it means the lamp needs to be changed.The red lamp staying on, also could mean a power problem. But,in any case, go ahead and change the lamp. Hopefully, it should fix the problem.Regards.

Check your fuse. May you replace with higher watt bulb so the fuse blown

Sir try to check this link http://www.tvscreenfinder.com/ good day

Hi,
Error code 18 in WD-73735 shows following problem..

Engine will not accept data (ASIC-READY signal from Engine is not detected).

and possible causes of this problem are...

1- Loss of 12V from PWB-POWER (Loose PE or PE2 connector)
2- Bad Color Wheel Loose J6 or J7 connector)
3- Engine Failure.

TV needs qualified and experienced tech to sort out problem and replace bad parts/ engine to solve the issue.
Hope these info will help.
Thanks.

Thats usually caused by the light engines optical block. very exspensive to repair

Get a hold of a dealer for these tv's. they usually have to discard all the boxes after deliveries. they should have one that they would gladly give you.