Fisher and Paykel WL37T26D Top Load Washer - Answered Questions & Fixed issues

main board blew

I would call the local engineer for a quote as you would need the repair manual to find the fault if you are able to read the diagram eric

How high does the drain hose go? If there is too much rise in the hose to the drain then it is building too much pressue when trying to drain.

Remove the small whit plugs and screws at the fron, you will see them when you remove the lid. Lift up top panel and you will see them there.

Need a new seal

Hi - with aquasmarts there is a plastic dome like fitting in the middle of the agitator & unscrew this to remove the unit.

Hi,
The washer filling so slowly can get very irritating and frustrating..most of the time the fix is very simple. The hoses have a screen in them to catch any dirt that may come in the water and this screen plugs up.
Simply unhook the hoses at the washer and clean the screens.

This tip will explain this in more detail for you..

Washing Machine Fix Washing Machine No Water
http://www.fixya.com/support/r3880533-washing_machine_fix_washing_machine_no

First try a power reset. Remove the power plug over night. Press and hold the power button for 1 minute. Plug back in. Or, the water level sensor needs replacing. https://www.google.com/search?q=Fisher+and+Paykel+top+loader+TOP+FULL+and+won%27t+wash ..

That sounds indicative or either a failed controller board or bad connections on it. What you can try if you wish is getting to the control board and spraying all the connecters with electrical switch cleaner. For any board edge connectors remove the connector, spray the contacts on the board edge and polish the board edge contact strips with a piece of kitchen towel. If that doesn't fix it call for service and diagnosis as control boards are expensive, so you need not only a correct diagnoses but warranty on the part and the labour. The other possibility as an afterthought, as the drain blockage caused this, is the pump working okay? These machines have self test procedures on the pump, and if the pump doesn't pass, the machine shuts down. If the drain was blocked and the pump was running for an extending time, it may be heat stressed. That would be a much cheaper repair. Further ideas in this link https://www.google.com/search?q=Fisher+%26+Paykel+Smart+Drive+Pride+5.5+Top+Load+turns+off+after+filling ..

https://householdmanuals.com/fisher-and-paykel/washer/mw512/download?page=4&landingTrack=brand-subcategory MW511 or 512

Check this out... https://www.justanswer.com/appliance/2ly8o-code-43-fault-fisher-paykel-intuitive-top.html Best to you.

Neither, call a domestic appliance service engineer.

Did he replace Bearings AND Seals. The seals protect the bearings from water damage and rusting. Apply lots of Water Pump Grease even if it is a supposedly sealed bearing. Also make sure they are genuine OEM bearings and not Chinese copies. This link shows two bearings and a seal. There is good advice at the bottom of the page. Not sure if for your model, but the advice is sound. https://partsdr.com/part/429565p-bearing-kit FWIW, front load washers are the way to go, except they take up a bit more footprint. They are far more Eco than any top loader. ..

Question edited for full maker name. This site does not do well with abbreviations. Question moved to maker category. It may be a failed control board, but a few things to try first.

Why Is My Fisher And Paykel Washing Machine Not Starting?

JustAnswer https://www.justanswer.com > Appliance Repair Jan 30, 2009 - 1.With the machine off: Press and hold the WASH TEMP DOWN button and then the POWER button until the machine gives 2 short beeps and lights up. 1 answer · Top answer: Unfortunately yes. The parts only come from Fisher and Paykel and the board....

Troubleshooting

Fisher & Paykel https://producthelp.fisherpaykel.com > QuickSmart Jul 6, 2017 Problem Possible Causes What to do Washer not turning on. Household power supply not working. Try plugging in anoth... Touching does not start the fill. Washer door not closed properly. Open and reclose door. Touching does not start the fill. Delay start maybe set. Refer to 'Wash cycle... View 47 more rows

The Start/Run Capacitor has failed. The capacitor give the motor a voltage jolt to get it going.

Capacitor - 7uF

Fisher & Paykel https://www.fisherpaykel.com > laundry-spare-parts Capacitor 7uF for Dryer. 400V. Note: Does not suit some older models with an Emmerson (square) motor. Capacitor - 7uF. $ 43.83. Add to Cart. $ 43.83Each. A$43.83

Capacitor 7uF 450V Fisher Paykel Dryer ED57, AD55AU ...

eBay https://www.ebay.ca > itm > Capacitor-7uF-450V-Fish... Capacitor 7uF 450V Fisher Paykel Dryer ED57, AD55AU 93214A, ED56AUFP, AD55AU ; Type. Capacitor ; Installation. Built-In/Integrated ; Compatible Model. ED57, AD55AU ... A$12.95

Fisher & Paykel Dryer Capacitor for Motor 7UF Microfarad

Steve's Appliance Spares https://www.appliancespares.nz > products > fisher-pa... Genuine ICAR Capacitor Genuine Manufacturer used by Fisher Paykel for dryers, ActiveSmart fridge-freezers and sold by spa pool stores across NZ DUCATI. NZ$13.03 ..

needs a new belt or the belt slipped off either way.. that is your issue

A short circuit in the motor is the most likely reason. You need a service engineer to correctly diagnose.

Try first resetting it..unplug for 5 minutes then plug back in to see if it resets to factory settings.

If you have already tried all the logical troubleshooting tips and the Fisher and Paykel Top Loader washing machine model WA7060 is still not turning on, there may be a few potential causes:

1. Power supply issue: Check if the power outlet that the washing machine is connected to is working correctly. You can test the outlet with another appliance or device. If the outlet is not working, you may need to call an electrician to fix it.
2. Control module or power board failure: If the power supply is not the issue, then there may be a problem with the control module or power board of the washing machine. In this case, it may need to be replaced or repaired by a qualified technician.
3. Faulty power cord: The power cord may be damaged or faulty, causing the machine not to turn on. Check if the power cord is properly connected and if there are any signs of damage. If there are, replace the cord with a new one.
4. Circuit breaker tripped: Check if the circuit breaker for the washing machine has tripped. If it has, reset the breaker and try turning the machine on again.

If you have already tried all these troubleshooting steps and the washing machine is still not turning on, it is best to contact a qualified technician to diagnose and fix the issue. They will have the tools and expertise to identify the root cause of the problem and recommend the best solution.

There could be a few possible reasons for the grinding noise in your Fisher and Paykel front loader washing machine. Here are a few things to check:

1. Check the drum paddles: If the drum paddles are worn or broken, they can create a grinding noise during the wash cycle. Check to see if any of the paddles are loose or damaged.
2. Check the drum bearings: The drum bearings are responsible for supporting the drum and allowing it to spin smoothly. If they are worn or damaged, they can cause a grinding noise. To check the bearings, try spinning the drum by hand. If it makes a grinding noise or feels rough, the bearings may need to be replaced.
3. Check the drive belt: If the drive belt is loose or worn, it can cause a grinding noise. Check the belt for any signs of wear or damage, and make sure it is properly tensioned.
4. Check the motor: A faulty motor can sometimes cause a grinding noise. If you suspect the motor is the problem, it's best to call a professional for assistance.

If none of these solutions fix the problem, it's best to call a professional to diagnose and repair the issue.