Jack Lalanne Health Master 100 Blender 8-Speed Blender - Answered Questions & Fixed issues


Hi nathanbenson,

The product has been discontinued and you might find it hard loking for a replacement part online. However, if you will call the manufacturer Tristar directly they can help you with this. You may call them at 973 575 5400 ext129.

Hope this helps.

Thank you for using FixYa.

Jack Lalanne... | Answered on Jun 20, 2011 | 158 views


I have been thru the fire about this! I sent my Healthmaster in recd another and it failed also. Almost always..it is the bearing that fails in the caraffe that supports the blade. The bearings that Jack Lalanne had installed in China..were not sealed...so they would allow water to enter corrode and eventually all of your blenders contents would come out thru the bottom! Or another thing that can happen is your blade will freeze up due to corrosion....and become immovable.
Jack Lalanne healthmaster is out of business. I manged to get a refund form Tristar..lalannes distributor..BECAUSE they authorized me sending my belnder back for a new one...and then they cashed my shipping check and then threw out my blender!!!!! I also had to call for weeks till I drove Tristar insane...so they ponied up teh dough
So I doubt you can receive any money.
But this is what you CAN do!
1) If your motor functions well..you can buy a new carafe for 45 dollars or so from Cooking toys ( google cooking toys and it should come up)
2) OR if your cheap like me...and your blade doesnt rotate easily due to corrosion and your caraffe isnt leaking much...put a couple drops of oil on the outter rim of the bearing ( That would be located directly on the bottom of the outside of the caraffe..it surrounds the knurled metal part that is inserted in the motor for blending.
My blade was corroded and leaking a tiny bit..I put some olive oil on the bearing and it worked great! I have ben able to use my caraffe for a month now...when I expected to have to buy a new one from "Cooking Toys" Which I will do if this one fails.
3) If you buy a new caraffe form cooking toys..my advice? OIL THE BEARING WITH A LITTLE OIL...(any kind of vegetable oil) AFTER EACH TIME YOU USE IT! I SUSPECT IT WILL LAST INDEFINITELY>>>BUT TIME WILL TELL!

Jack Lalanne... | Answered on Apr 12, 2011 | 1,025 views


YES

Jack Lalanne... | Answered on Mar 04, 2011 | 280 views


You did not specify where the leak is coming from, so I can only guess and my guess is the base. Assemble gasket first, then blade plate and then base retainer. You can tighten the base tighter while the unit is on the motor base. the motor base will let you get it slightly tighter.

Jack Lalanne... | Answered on Dec 12, 2010 | 339 views


Check your local restaurant supply store. You may want to go to google to see where the best place is, if you live along the rocky mountain region here is a great place that should have it http://www.standardrestaurant.com.
If that doesn't help then whoever sold you the blender may have more answers.

Jack Lalanne... | Answered on Mar 12, 2010 | 183 views


Take your motor to a small appliance repairman. It might just be a loose wire..inside that needs replaced or re connected then follow my tips below.





I have been thru the fire about this! I sent my Healthmaster in recd another and it failed also. Almost always..it is the bearing that fails in the caraffe that supports the blade. The bearings that Jack Lalanne had installed in China..were not sealed...so they would allow water to enter corrode and eventually all of your blenders contents would come out thru the bottom! Or another thing that can happen is your blade will freeze up due to corrosion....and become immovable.
Jack Lalanne healthmaster is out of business. I manged to get a refund form Tristar..Lalannes distributor..BECAUSE they authorized me sending my blender back for a new one...and then they cashed my shipping check and then threw out my blender!!!!! I also had to call for weeks till I drove Tristar insane...so they ponied up the dough
So I doubt you can receive any money.
But this is what you CAN do!
1) If your motor functions well..you can buy a new carafe for 45 dollars or so from Cooking toys ( google cooking toys and it should come up)
2) OR if your cheap like me...and your blade doesnt rotate easily due to corrosion and your caraffe isnt leaking much...put a couple drops of oil on the outter rim of the bearing ( That would be located directly on the bottom of the outside of the caraffe..it surrounds the knurled metal part that is inserted in the motor for blending.
My blade was corroded and leaking a tiny bit..I put some olive oil on the bearing and it worked great! I have ben able to use my caraffe for a month now...when I expected to have to buy a new one from "Cooking Toys" Which I will do if this one fails.
3) If you buy a new caraffe form cooking toys..my advice? OIL THE BEARING WITH A LITTLE OIL...(any kind of vegetable oil) AFTER EACH TIME YOU USE IT! I SUSPECT IT WILL LAST INDEFINITELY>>>BUT TIME WILL TELL!

Jack Lalanne... | Answered on Jul 08, 2010 | 403 views


I wish I could tell you a definite solution. Have you tried calling 973-575-5400 (ext 129)? I realize it isn't toll-free. According to several web sites, the manufacturer has discontinued the product, but they should definitely still be supporting the motor warranty.

Mine is eating the bearing in the bottom of the pitcher. That seems to be everyone's most frequent problem although mine hasn't actually started to leak yet. The motor is just fine. I suspect Jack Lalanne started getting complaints about the pitcher bearing and dropped his support for the product because of that.

Jack Lalanne... | Answered on Jul 08, 2010 | 500 views


Jack Lalanne is out of the blender business. The bearing that surrounds the Knurled piece that you insert in the motor each time you blend are not "sealed" so consequently water gets in there and causes them to fail.
They only thing you can do...is to buy a new caraffe from Cooking Toys ...google it...
It will cost you 45 bucks plus shipping dont buy any extras!
After you receive it BE SURE to oil ( a couple drops will do)the bearing that surrounds the knurled piece that is inserted into the motor each time you blend. Inthis way the unseale dbearing will remain lubricated and will last you awhile. Mine became frozen and I was able to un freeze it and my bleender works fine now for months! An dI use it 3 times a day! I expect I will have to buy a new caraffe..in the future because of corrosion...that I could have prevented with oil.
Any questions? gmcgeary@gmail.com

Jack Lalanne... | Answered on Jul 08, 2010 | 499 views


First determine..if it is indeed the motor that is fried. Do this by not using the caraffe. Plug in the motor and run it by itself. If it runs fine without smoking again..It is the caraffe that is defective.
If its the motor you are out of luck completely. Jack Lalanne is out of business.
If it is the caraffe..which I suspect it is not...oil the rim of the bearing that is on the outside of your caraffe ..it surrounds the knurled part that is inserted into the blender...even if you are able to get the motor repaired..get in the habit of oiling the caraffe bearing after each time you use it. If you dont it will fail within months to a year of use
Lalanne had they made in China..and using unsealed bearinga that rust out and the contents of the blender come out!! So I discovere dthat oiling that part each time after use..keeps my blender running smoothly.
You might want to take yoru motor to a small appliance repairman..he might find something simple happened.. like a loose wire connection inside! If he does...you have a simple solution and a motor that works!
Remember to oil the bearing a couple drops each time after use...and if yoru caraffe ever fails you can buy a new one..( Oil that one too!) at Cooking Toys..you can google for the address
gmcgeary@gmail.com

Jack Lalanne... | Answered on Jul 16, 2014 | 1,288 views


Yes Ive been thru this...I recd a refund due to luck.
You can buy a new caraffe at Cooking toys..for 45 bucks.

If your motor is working...just oil the bottom of the caraffe each time you use it! It shoudl keep it going for a long time.
What I mean by oil teh bottom..Is ...oil with any vegetable oil....the rim of the bearing on the outside of the caraffe..it surrounds the metal knurled piece that is inserted into teh motor each time you blend.

Jack Lalanne... | Answered on Jul 08, 2010 | 577 views


It Could Be a Number of Things..
It's most likely that the electrical Wire Could Have a Shortage, If it cuts off again Try gently Wiggling the Electrical Wire in a Number of Directions If it cuts on and off while your fidgeting with it, you've found your Problem! A quick fix would be to Adjust the wire In the position it would cut on the strongest, wrap the cord with Tape to Keep the wire in that Position, this will Prevent it from shorting again.
Either that or you simply put too much product in the Blender with an inadequate amount of liquid.

Blenders | Answered on Oct 06, 2019 | 1,776 views


typically, you can't repair it.

Blenders | Answered on Sep 14, 2019 | 59 views


that happens to the best of them. Try heat soap, vinegar, and a tight grip to get it off.

Blenders | Answered on Sep 14, 2019 | 32 views


blenders are:
power cord, switch, speed control, and motor.
A disassembly and VOM meter is required to determine which part is defective.

Blenders | Answered on Sep 14, 2019 | 40 views


Use https://www.google.com and the words manual and whatever manufacturer and model it is to see manuals.

Blenders | Answered on Sep 11, 2019 | 42 views


ask ninja for a warranty replacement

Blenders | Answered on Sep 08, 2019 | 52 views


Fixya does not sell Intertek parts. Intertek might be a source.

Blenders | Answered on Aug 25, 2019 | 35 views


Is probably a binding problem with the motor shaft bearing or the circuit card is fried. If you've tried giving it a good cleaning and that didn't work it's a good bet the unit is junk. Suggest buy a new one.

Blenders | Answered on Aug 17, 2019 | 91 views

Not finding what you are looking for?
Jack Lalanne Health Master 100 Blender 8-Speed Blender Logo

38 questions posted

Ask a Question

Usually answered in minutes!

Top Jack Lalanne Blenders Experts

eyecam

Level 2 Expert

96 Answers

Marvin
Marvin

Level 3 Expert

85178 Answers

Ross Keen

Level 3 Expert

1351 Answers

Are you a Jack Lalanne Blender Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...