Jura Capresso Jura / Capresso IMPRESSA J5 Espresso Machine - Answered Questions & Fixed issues

Hi, I made a video how to fix your Jura step by step, good luck.! http://fixandparts.wix.com/nicknicoloudis#!jura-coffee-machine/c15gy

Hi, I made a video how to fix your Jura step by step, good luck... http://fixandparts.wix.com/nicknicoloudis#!jura-coffee-machine/c15gy

Hi Jeni But.... does it self rinse when you Power Up? Saving Water

Try putting a container under the coffee spouts and pressing the rinse button. This will usually free any coffee grounds that may not have been expelled into the grounds basket from the last time the machine was used. The grounds can get stuck and block the slide path of the grounds basket.

Sometimes certain beans do not move freely throughout the grinder. Oily beans, which is not necessarily a bad thing, do not fall into the grinder easily and tend to stick. It is necessary to sometimes to just poke or stir the beans around with your finger to make sure they fall into the grinder. For a safety measure do this while your machine is turned off.

i have this same problem any solution yet?

Unfortunately, without being there in person to inspect the machine and its components, it's difficult for me to provide a definitive answer. However, I can offer some general guidance that may help:

1. Consult the user manual: The user manual for your Capresso C3000 should have a diagram or schematic showing the different components and their connections. If you still have the manual, check to see if there's a helpful diagram inside.
2. Look for visual cues: While it can be difficult to identify the tubes by sight alone, there may be visual cues that can help you narrow down which tubes go where. For example, one tube may be thicker or more flexible than the others, or it may have a different color or texture.
3. Experiment with different configurations: If you're unable to find a diagram or visual cues, you may need to experiment with different configurations until you find the correct one. This can be time-consuming and frustrating, but it may be the only option if you're unable to find any other information.
4. Seek professional help: If you're still unable to identify the correct tube configuration, you may want to consider seeking professional help. A qualified technician or repair service may be able to identify the correct configuration and get your machine back up and running.

I hope this helps, and I wish you the best of luck in getting your Capresso C3000 back in working order!

http://www.fixya.com/support/t12615678-capresso_303_will_not_steam

Talk him

The first thing to check is the seating of your water tank. Just a few grains of coffee grounds or dirt underneath the tank are enough to break the watertight seal. Make sure the area under the tank is absolutely clean. That's always worked for me when I've had the leaking problem.

Rinsing cycle at start up is electronically programmed function. Unplugging is a temporary solution. Jura will not sell parts or offer any guidance. I could look into more details to find an answer but the model Capressa 50 is not listed in my Data base. Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/edward_bbd2c7ff4ee1828a

TRY SWITCHING IT OFF AND RETRY LATER MAY BE IT WILL RESET IF NOT CHECK FOR ERROR OR TELL US MORE ABOUT THE FOULT

You really don't give which machine - but here is link to company product support. Maybe they will have product manual to help trouble shoot issue. Sorry could not of been more help Product Support

The switch or photo sensor is not sensing any beans present. So it can't continue Use torch to inspect bean entry area Small brush etc

Hi Marton Registered repairers love you guys.... If you carry a smartphone these days and most of us do. You need to learn to take photo's first. Even the Las Vegas pro restoration guy on TV does that. Sorry I don't have those photos and you'll be really lucky is someone on Fixya does. Try YouTube videos.

What model do you have? What's the problem you are trying to fix by resetting it?

Just a guess here but if you are not using soft water you may have a hard water scale coating on the sensor. The sensor is preventing the heating element from powering up because it thinks there is no water. Try filling the machine with vinegar for several hours (no more than overnight) This will dissolve hard water deposits and hopefully clear the sensor. (the sensor should be a simple continuity contact. If you can look inside and see a metal button and it is fouled clean it off.)

Try running distilled white vinegar through it.

constant heating message on screen is from a thermal fuse blown on one of the boilers. service call required i'm afraid...... very cheap part about 10 euro

Try applying hot water around the dish to expand and unstuck while gently but firmly pull the tray. It went in so must come out.