Jura Capresso Jura / Capresso IMPRESSA Z6 Espresso Machine - Page 9 - Answered Questions & Fixed issues

Hi, isolated calcium should have a 2+ charge at the atomic level. So what every you use has to have a negative charge to have the best chance at removing the calcium. These means you need a base of some sort, so you might consider cleaning with baking soda or potentially olive oil. Please reference a period table to find more negatively charged elements (should be on right side of the table). Thank you.

Roomba: Error 2

https://prod-help-content.care.irobotapi.com > en-US Error two (2) means the extractors or brushes cannot turn. Please perform these care procedures for your robot: Roomba e Series and Roomba i Series rubber brush ...

Saeco XSmall : Cannot put brew group back in... Turns out the drive gear in the main machine is mis-aligned. This can happen if you try to remove trays or open the service door while the machine has not "finished" a brewing cycle (coffee may be done, but the machine is not!). Confirm this by looking at the drive shaft. It has 5 splines, and two are much wider than the other 3. Those wider ones should be on the top--if they are in any other position, then it does not match the "neutral" position in the brew group and the brew group cannot be inserted. Unless there is something else wrong, the machine will re-align itself during the power-on self-check, but in order to trigger the self-check, you have to fool it into thinking that all the trays, etc. are installed (essentially, bypass all relevant microswitches). This doc has some details and pictures of what to look for: https://www.coffeetico.com/SAECO_pdf_files/BrewGroupRemoval.pdf. For the XSmall, leave the brew group out, shut the service door and put the grounds bin in. Also, make sure the water bin and drip tray are in as normal. This is enough for the XSmall to startup. Turn the machine on and as it does its self-check, the gears get re-aligned properly. It will eventually figure out the brew group is missing and start flashing red--turn the machine off at that point. Verify that the two wide splines are at the top. The brew group should now slide in easily.

It's not a well known machine so no fault data on it. Find a local dealer and take it to them. https://www.google.com/search?q=My+Scholars+Espresso+system+displays+%27fault+on+water+system%27 ..

A 3 way valve is a series of chambers that divert liquid or steam. A solenoid is the electronic device that makes those valves open and close. Solenoids are the things that fail the most, but often due to the valves sticking. https://www.google.com/search?q=livia+90+parts ..

https://tatring.com/getting-pierced/How-to-care-for-a-new-piercing

Place the tank under a water tap and turn the water tap on.

Has anyone figured out the cause of this and how to fix it?

Stesso problema risolto cambiando la scheda pcb con una nuova. Chiss? se esiste un modo per riprogrammare la scheda non funzionante.

Use a handheld pipe cleaner, after that flush out with hot water and two table spoons of vinegar.

If you have positioned the frother properly and there is an adequate amount of milk and the frother still not working then there might be some kind of damage to the internal parts of the machine. You can buy replacement parts for Keurig frother easily online. Read this article for further details.

Jura Capresso Impressa E8 Espresso/Coffee Maker Error 8 ...

www.fixya.com > ... > Jura Capresso Impressa E8 Espresso/Coffee Maker

Jura Capresso Impressa E8 Espresso/Coffee Maker, error 8 related issues. Get free ... We have just done a full disassembly, cleaning, and relube of our Jura Z5 ...

Bosch Benvenuto B30 Espresso/Coffee Maker Error 8 ...

www.fixya.com > ... > Bosch Benvenuto B30 Espresso/Coffee Maker

This normally means it needs a good clean and that the Neoprene piston o-rings need to be changed. With age, heat and use, they loose their slippiness.

vinegar

need to take apart to narrow down leak --problem --

Question edited for clarity. There is no service manual listed. The ball bearing is likely part if a none return valve. Contact Sprada direct in Switzerland. https://www.google.com/search?q=sprada+future+service+manual No Parts Lists either. They are a secretive company. https://www.google.com/search?q=sprada+future+parts+list ....

Make and Model is useful in these questions as many machines share the same known fault. It you are talking about the milk frother steam wand, they always get blocked with scorched, dried milk. You need to soak in a specialized milk enzyme cleaner.

no info generic answer water lines are a sealed system --can disconnect feed line and inject it into line then reconnect and run water