Jura Capresso Jura / Capresso IMPRESSA Z6 Espresso Machine - Page 7 - Answered Questions & Fixed issues
Hi, I'm using the machine coffee Jura ENA Micro 90. when I start to make a cup of coffee, the grinder is working until the cup of coffee is done.
It sounds like there may be an issue with the grinder's programming or calibration. Here are a few steps you can try to resolve the issue:
- Check the grind settings: Make sure the grind setting is not set too low, as this can cause the grinder to continue grinding even after the brewing process has started. You may need to adjust the grind setting to a coarser level.
- Clean the machine: If the grinder is clogged with old coffee grounds, it may continue to grind to compensate for the lack of coffee being produced. Clean the machine thoroughly, including the grinder, and try again.
- Reset the machine: Turn off the machine and unplug it for a few minutes, then plug it back in and turn it on again. This can sometimes reset the machine and resolve any software or programming issues.
- Contact Jura customer service: If none of the above steps work, it may be necessary to contact Jura customer service for further assistance or to schedule a repair.
I hope this helps!
Pipe Pro 304 not revving up when starting arc
If your Miller Pipe Pro 304 is not revving up when starting the arc, there are a few things you can check:
- Check your fuel level and make sure you have enough fuel in the tank. If the fuel level is low, the engine may not have enough power to rev up.
- Check the battery voltage and connections. If the battery voltage is low or the connections are loose or corroded, the engine may not start or rev up.
- Check the air filter and make sure it is clean. A dirty air filter can restrict airflow to the engine and reduce its power.
- Check the spark plug and ignition system. A faulty spark plug or ignition system can cause the engine to run poorly or not rev up.
- Check the throttle control and make sure it is set to the proper position. If the throttle control is set too low, the engine may not have enough power to rev up.
If none of these solutions work, it may be necessary to take your machine to a professional for further diagnosis and repair.
My Palazzo coffee machines after making a cup all the lights started flashing and then went dead. is there a fix?
It's difficult to determine the exact cause of the issue without further information or inspection. However, you can try the following troubleshooting steps:
- Check if the machine is properly plugged in and the outlet is functioning.
- Check if there is water in the reservoir and the water tank is properly seated.
- Check if the machine's components are clean and free of any blockages or clogs.
- Reset the machine by unplugging it for a few minutes and then plugging it back in.
- If none of the above steps work, you may need to contact the manufacturer or a professional repair service for further assistance.
It's also possible that the machine may have a faulty control board or power supply, which may require replacement.
I have a Jura ENA Micro 9 One Touch coffee machine, I was going to start a cleaning cycle and then Close Cover screen came up, even tho the cover was closed. I tried everything and nothing worked!
If the "Close Cover" screen is coming up on your Jura ENA Micro 9 One Touch coffee machine even though the cover is closed, there may be an issue with the cover sensor or the machine's internal sensors. Here are a few things you can try to resolve the issue:
- Double-check that the cover is securely closed: Make sure that the cover is firmly in place and not obstructed in any way. Remove any excess coffee grounds or other debris that may be blocking the cover.
- Power cycle the machine: Turn off the machine and unplug it from the power source for a few minutes. Then, plug it back in and turn it on to see if the issue is resolved.
- Perform a reset: Some Jura coffee machines have a reset function that can be accessed by pressing and holding down certain buttons. Check your machine's user manual to see if there is a reset function and how to access it.
- Contact Jura customer support: If none of the above solutions work, it may be necessary to contact Jura customer support. They will be able to provide you with further troubleshooting steps or arrange for a repair or replacement of your machine if necessary.
Note: Before attempting any maintenance or repair work on your Jura coffee machine, be sure to unplug it from the power source and read the user manual thoroughly.
Steam is coming out of the top of the unscrew button when the water is heating the frother on my DeLonghi Icona Vintage coffee maker it then blows the fuse.
It sounds like there may be a blockage or pressure build-up in the frother or in the steam wand of your DeLonghi Icona Vintage coffee maker, which is causing steam to escape from the unscrew button and blow the fuse. Here are a few things you can try to fix the issue:
- Clean the frother and steam wand: The blockage may be caused by a build-up of milk or other debris in the frother or steam wand. Try cleaning them thoroughly with hot water and a cleaning solution designed for espresso machines.
- Descale the machine: If the blockage is caused by mineral build-up, descaling the machine may help to remove it. Follow the manufacturer's instructions for descaling your specific model.
- Check the pressure release valve: There may be a problem with the pressure release valve, which is causing steam to escape from the unscrew button. Check the valve and make sure it is not blocked or damaged.
- Contact DeLonghi customer service: If none of the above steps resolve the issue, it may be a problem with the machine's internal components. Contact DeLonghi customer service or a qualified repair technician for further assistance.
It's important to be careful when working with steam and hot water, so make sure to follow all safety instructions and precautions when attempting to troubleshoot or repair your coffee maker.
How to open an Inventum KZ718D coffee machine?
To open an Inventum KZ718D coffee machine, follow these steps:
- Unplug the coffee machine from the power source and wait for it to cool down completely.
- Remove the glass carafe and the filter basket from the coffee machine.
- Turn the coffee machine upside down and locate the screws on the bottom of the machine.
- Use a Phillips head screwdriver to unscrew the screws and remove the bottom panel of the machine.
- With the bottom panel removed, you should be able to access the inside of the machine and any components that may need to be repaired or replaced.
It's important to exercise caution when working on electrical appliances. If you're not comfortable working with electrical components or if your coffee machine is still under warranty, it may be best to seek the assistance of a professional repair technician.
My magic wand stopped buzzing but it brings light
If your magic wand is not vibrating anymore, there might be a few potential reasons for this:
- Battery: The battery may be dead or running low. Try charging or replacing the battery to see if this solves the issue.
- Motor: The motor in the wand may be worn out or damaged, preventing it from vibrating. This can happen over time with frequent use.
- Wiring: There may be an issue with the wiring inside the wand that is preventing it from vibrating.
As for the light still working, it is possible that the light and vibration functions of the wand are controlled by different components.
If you are unable to determine the cause of the issue, it may be best to contact the manufacturer or a professional repair service for assistance.
Descaled and now descale light will not go out even after power off and reset pressed 10 secs
If your descale light is still on after descaling your coffee maker or espresso machine and performing a power off and reset, there are a few things you can try:
- Double-check that you followed the descaling instructions correctly. Make sure that you used the right amount of descaling solution and water and that you let the machine complete the entire descaling cycle.
- Try unplugging the machine from the power source and letting it sit for several hours. This can sometimes reset the descale light.
- Check the user manual for your machine to see if there is a specific way to reset the descale light. Some machines require you to hold down certain buttons or perform a specific sequence of button presses to reset the light.
- If none of the above steps work, there may be an issue with the machine's sensors or circuitry. In this case, it may be best to contact the manufacturer for further assistance or to have the machine serviced.
CVA-615 Seems to have water blockage before Brew Unit
If the hot water spout and steam wand are functioning normally, but there is no water coming out of the coffee spouts during the rinse cycle, it is likely that there is a blockage in the water pathway leading to the brew unit.
Here are some possible causes and solutions:
- Water filter: If your machine has a water filter, check to see if it needs to be replaced or cleaned.
- Water tank: Check the water tank to make sure it is properly seated and that the water level is sufficient.
- Water pathway: The water pathway from the tank to the brew unit may be blocked with scale or debris. Try running a cleaning solution through the machine to clear the pathway.
- Brew unit: If the above solutions do not work, the problem may be with the brew unit itself. Check to see if it is properly seated and clean. If it is damaged or worn, it may need to be replaced.
If the problem persists, it may be necessary to have a professional technician inspect and repair the machine.
Hi, my carezza builds up pressure, but the water that comes out is a trickle, even when I've removed the group head. Steamer wand works, but I can't get enough force to make an espresso.
It sounds like there may be a blockage in the coffee delivery system of your Carezza. Here are some steps you can take to troubleshoot the issue:
- Check the filter basket: Make sure the filter basket is clean and clear of any coffee grounds or debris that could be causing a blockage.
- Clean the group head: Remove the group head and clean it thoroughly with a brush and hot water. Pay special attention to the holes where the water comes out.
- Check the water tank: Make sure the water tank is full and properly seated in the machine. If the water tank is not seated properly, it can cause low water pressure.
- Descale the machine: Over time, mineral deposits can build up in the machine and cause blockages. Descaling the machine can help remove these deposits and improve water flow.
If these steps do not resolve the issue, it may be necessary to disassemble the machine to check for more serious blockages. If you are not comfortable doing this yourself, it is recommended to take the machine to a professional for repair.
Jura Impressa C9 Grounds container filling with water or Coffee. Grounds floating.
It sounds like there may be a blockage in the brewing unit or the drainage system causing the water and coffee grounds to back up and overflow into the grounds container.
You can try cleaning the brewing unit by removing it from the machine and rinsing it with hot water. Be sure to clean all the nozzles and crevices to ensure there is no blockage.
You should also check the drainage system for any clogs or obstructions, such as coffee grounds or debris. This can be done by removing the drip tray and examining the drainage hole at the bottom of the machine.
If these steps do not resolve the issue, it may be necessary to contact a professional for repair or servicing of the machine.
User manual for a crofton TI-CM-1013 COFFEE MAKER WITH THERMO JUG
Unfortunately, there is no user manual available for the Crofton TI-CM-1013 Coffee Maker with Thermo Jug. However, it is possible that the warmer plate can be switched on by pressing the "on/off" button. If this does not work, then it is likely that the warmer plate is not functioning properly and may need to be replaced.
Jura Impressa C5 all lights are flashing, Cant descale or clean. What do I do?
When all the lights on your Jura Impressa C5 are flashing, it typically means that the machine is experiencing a malfunction or error. Here are a few steps you can try to troubleshoot the issue:
- Turn off the machine and unplug it from the power source for a few minutes, then plug it back in and turn it on again. This can sometimes reset the machine and clear the error.
- Check the water tank and make sure it is filled to the appropriate level. If the water tank is empty or low, the machine may not be able to function properly.
- Check to see if the brew group is properly seated in the machine. If the brew group is not properly seated, the machine may not be able to start a brewing cycle.
If none of these steps work, it's possible that there is a more serious issue with the machine that may require professional repair. In that case, you may want to contact Jura customer service or a professional appliance repair service for further assistance.
Brand new Lavazza Desea coffee machine - frother is losing steam around the head and not enough froth to make latte. Help!
1. Fill the water tank: Fill the water tank with cold water and make sure the tank is securely in place.2. Load the coffee beans: Open the top lid and fill the funnel with coffee beans of your choice.3. Select the desired program: Use the selection buttons on the front panel to choose the desired program.4. Start the machine: Press the Start/Stop button to start the machine.5. Wait for the desired coffee: The machine will grind the beans and dispense the desired coffee in a few seconds.6. Empty the grounds container: Remove the grounds container and empty it.7. Rinse the components: Rinse the funnel and the other components with hot water after each use.
Not finding what you are looking for?
