20 Most Recent
Bunn 37600.0000 - Page 6 Questions & Answers
After brewing with a Bunn MCU, it does not fully use all of the water; some remains in the coffee pod. It does this with all textures of coffee grounds. It makes cleanup a mess. Any ideas? Thanks!
First, Though I have worked on many Bunn commercial systems. I'm not quite familiar with the newer MCU though I've worked on similar single cup home systems.
* Most single up systems like the Cup/Pod/Capsule usually have a air flusher that pushes all the water out of the brewer to extract all the flavor and prevent old liquids left in unit.
* If your still dripping, have wet pods/capsules/cups, then it sounds like the air pump is not turning on or not working properly. Bad pump could be a cracked or loose hose as the pumps don't really wear out as it's only air (hopefully clean air, no dust). Call for service.
* The brew cycle might not be completing thus not continuing on to the next step which is to pump air in. Brew sensor or timer out. call for service
* Computer is out or fried (especially after an electrical storm). Call for service.
* Finally, most of these home units do not have serviceable parts. Most take at least an hour to service. So if your not in the warranty period it may not be worth fixing. But be sure to call your service provider or MFR for advice.
Aloha! ukeboy57
We have a C Series Bunn single coffee make that has two different sized clear plastic water hoses connected with a barbed fitting. I can not find a manual that shows me this fitting.
It sounds like the T-Barbed fitting on top just before the brew head. There is a water by-pass system on large commercial brewers. The idea is that it's possible to over-extract the ground coffee if too much water is poured into the worn out ground. There are several types of systems and ideas on how to overcome this problem. over extraction is one of the causes of bitter coffee. You've tasted old peculated coffee from old brewers of the 1950-60's.
* the t-barb fitting comes from the main brew head valve then tees off to the bypass port which can have another solenoid or just a pin valve. the pin valve is manually adjusted to flow anytime the brew head valve is turned on. water is partially diverted to by-pass the grounds and drips directly along the inside of the brew funnel. Open it too much and you get weak watery coffee. Too little then stronger bitter coffee. I suggest turning it all the way clockwise (off) then opening it 3-1/2 turns. Check and adjust to taste.
* you should call your vendor for service and parts if needed.
* Parts are available from Bunn vendors,, Amazon, or your local restaurant supply as Bunn is a very common brand. Curtis parts may fit too. The barb is a standard 3/8th T fitting if I remember right. You may also find it at a Refrigeration plumbing supply like COSCO plumbing (Not the COSTCO membership store)
* It's just a divert-er so even a nylon t-fitting may work.
* Final; you can find the parts and manuals from Bunn.com even some of the discontinued models.
Aloha! ukeboy57
My bun coffee maker model vps will not heat the water. I did notice bubbling noise the last couple of months, any thoughts?
VPS are pour over brewers. Like the 12 cup brewers you find at home, they need to be filled with 12 cups of water (a full pot), heated and then peculated over the coffee grounds and collected in a decanter.
BUT there is one main difference! The VPR and similar COMMERCIAL coffee machines are quick brewers. They usually have a pre-heated pot of water stored inside the machine.
* VPR's and similar machines REQUIRE a pre-fill and heating period prior to brewing. This means it's sitting on a level table and filled with water until water sprays from the brew head. At this point the unit is plugged in and the heater is turned on (CWTF's have a toggle switch behind the machine). Brewer will pre-heat the water (there may be some water discharge from brew head as the water expands). Ready light will come on in about 15 mins.
* To Brew; Place coffee grounds in filter, place in funnel and brew head, clean empty decanter under funnel, slowly pour one full decanter of water (cold or hot) into brew tray. Do not overflow tray. Allow water level to sink before adding more water. Only fill with one pot as an equal amount will come out the brew head and funnel.
* FYI Coffee grounds are usually in pre-messured packets for office use. A simple guide is one tablespoon per cup. (level or heaping spoon is up to you)
* Since your brewer was bubbling at one point. I'm guessing it had water in the pre-heater at one time. But if it's not in use and left plugged in all that time then the water has probably boiled off. Hopefully someone unplugged the brewer prior to the unit blowing the thermal fuse.
* You can test the VPR by following the Pre-fill instructions I've listed earlier. If the brewer heats up and does not continuously boil (shorted condition) then try a brew. If it works then your okay. Otherwise the unit will need service for a blown high limit or bad heater element.
* Call your coffee vendor anyway. Many coffee vendors will service your brewer of even replace it as long as you buy coffee from them. Ask around.
Aloha, ukeboy57
Month Old Bunn smells hot
Bunn machine smells hot
* Check for unusual sounds from brewer (other than sizzling from warmer plates). There should be a gradual boiling sound accompanied by some steaming at the top of brewer. This will turn off and ready light indicating the brewer is ready to brew.
* You may sometimes hear a slight boiling sound from time to time (about 15-30 mins apart). Notify your vendor as the warmer blanket may be out. (your brewer will still work but call them anyway.)
* Check your manual for setting up procedures and checks. It's available on line: http://www.bunn.com/product-manuals
* Constant boiling (more than 15 mins) with lots of steaming is a sign of an electrical problem. Unplug machine and call vendor for service.
* Final; Unplug unit and check for 'stuff' in pour over tray. I've found Chocolate, Cream, Milk, powder, sugar, honey, and a dead rat in the tray. Crew will repour old coffee or beverages into brewer to 're-heat' them. Notify vendor for cleaning or replacement (it happens all the time.)
Aloha, ukeboy57
Our Bunn VRP SERIES MAKES NOISE WHEN WATER IN THE TANK SITS AWILE
There are two heaters in a VRP unit (Pour over style) The brewer has a tank that your last office person poured in a full pot of water. The main heater senses the colder water and begins to reheat the water to near boiling. The new water pushes out the same amount of water into the brewing basket (funnel with coffee). Once the new water has come up to temperature then the main heater turns off. There is a warming blanket around the inside tank. This keeps the water hot and ready to brew. It uses less power than the main heater. If this blanket fails then the water will cool down to a point where the main heater heats everything back up. You may not notice this as the only indication is luke warm coffee on a freshly made pot or a 'boiling' noise every 15 - 25 mins. This VRP probably needs servicing (check Thermal blanket and Thermal fuse)
My Bunn nhbx-b leaks water when brewing coffee
you could remove the cover and look for the connection that isn't connected properly - - be careful not to touch electrical connections/bare wires when cover is off - or take it to a technician - or contact Bunn directly for suggestions.
regards,
Not finding what you are looking for?