Top 10 Linksys WRT54G2 Wireless Router Questions & Answers

http://www-ph.linksys.com/servlet/Satellite?c=L_CASupport_C2&childpagename=PH%2FLayout&cid=1166859837401&pagename=Linksys%2FCommon%2FVisitorWrapper&lid=3740141396B01

By default the router's IP address is 192.168.1.1 so you need to make sure that your computer is connected on the router first with the cable. Make sure lights are lit up properly as well.

For you to be able to access the router setup screen, you need to OPEN IE and type on the address bar 192.168.1.1 no username and password is admin in lowercase.

Hope this works!

Im not sure but you could try this?
1)Get on your computer 2)Press Start>Run 3)then type cmd 4)Type ipconfig then hit enter 5)Type ipconfig /release then hit enter 6)type ipconfig /renew then hit enter 7)try your internet

Which network settings are you trying to write? In general, try getting Network Magic. It's a free download and trial and can help with some Linksys/Cisco problems.
Also, you may try getting into the firmware itself. Use any web browser and enter the following IP address as your URL: 192.168.1.1. At that point you're directly accessing the settings on the router and should be able to make any changes you need. By the way, this only works if you're connected directly to the router via Ethernet cable.

You will need to check the wireless settings of the router .
Is there any computer connected to the router with the Ethernet cable?
If not then connect 1 computer to the router and open the router set up page. Once you open the router set up page, you will be able to find the wireless network key.
Use that password to connect to the wireless network

Click Here for step by step Instructions on how to find the network key

Are you trying to set up the router.
You can do it manually without the CD.
Make sure that your computer is able to go online through the modem.
If your computer is not able to go online through the modem then you will need to call ISP first.
If your computer is able to go online through the modem
then you need to connect the computer to the router and the modem to the router.
open the set up page of the router and change the settings of the router according to the ISP.
Click Here for step by step by instructions

The router can be set to factory default by performing either of these two steps:

Resetting the Router Using the Reset Button
Resetting the Router Using the Web-Based Setup Page

NOTE: Pressing the Reset button on the back of the router for 30 seconds will reset your router to its factory default settings. All of the settings of the router will then be erased and the router's IP address will become 192.168.1.1.

To perform a hardware reset on your Linksys router, follow these steps:
Resetting the Router Using the Reset Button
Step 1:
Take note of the current settings of the router before resetting.
Step 2:
Press and hold the Reset button of the router for 30 seconds.

Figure 1: Location of the Reset button on a Linksys BEFW11S4 router.
NOTE: The image may vary depending on the model number of the Linksys device.

Figure 2: Location of the Reset button on a Linksys WRT54GX router.

Figure 3: Location of the Reset button on a Linksys WRT54GC router.
NOTE: If the image of your router looks different from the ones shown above, consult your router documentation.
Step 3:
If the normal reset does not work, try to press and hold the Reset button for three seconds. The Ethernet light should go OFF then back ON. Unplug and re-plug the router's power adapter while pressing the Reset button. Keep holding the reset until the power light stops blinking.
NOTE: The router must be powered ON when you press the Reset button.
To reset the router via its web-based setup page, follow the steps below.
Resetting the Router Using the Web-Based Setup Page
Step 1:
Access the router's web-based setup page. For instructions, click here.
NOTE: To learn how to access the router's web-based setup page using a Mac computer, click here.
Step 2:
When the router's web-based setup page appears, click Administration then click on Factory Defaults.

NOTE: If the screen on your router's web-based setup page looks different, click here.
Step 3:
Click on Restore Factory Defaults and select Yes.

Step 4:
Click OK.

Related Articles:

Accessing the Router's Web-Based Setup Page
Setting-Up a Router with Cable Internet Service
Setting-Up a Linksys Router Using DSL Internet
Changing the Linksys Router's Password

This is the direct link to the Firmware update simply scroll down and under Firmware click download.
http://homesupport.cisco.com/en-us/wireless/lbc/WRT54G
copy and paste into address bar.

What drivers do you want to download?
There are not drivers for Linksys router. It works on a software called as firmware?
How many wireless computers do you have?
What is the operating system on your laptop?
If your wireless network is secured then make sure that you have the correct network key.

See How to setup Linksys router
See how to connect to the wireless network

change the security type of router to WEP and password accordingly.
Now disconnect the samsung galaxy phone from internet and try to connect it back with new password. you will be able to access the internet.
It is resolved.