Top 20 Casio G-Shock Atomic MTG930DA 8VCR watch Questions & Answers

For all those who lost their Casio watch manual. Follow this link, fill in the requested details and download manual. http://world.casio.com/wat/download/en/manual/
you haven't got instructions on how to do this, you can get
instructions from the Casio web site.

Go to the casio web site "casio.com".

Select "support" and the "manuals",
watches;

Accept terms

Select "watch manual archive"

Read the number of the back of your watch and enter it into the search box

Hi,
In order to remove the links of your Mtg930 watch you will need a couple of tools . It is recommended to have a watch pin pusher and a spring bar remover tool in order to do so. If you do not you can use a small precision flat head screw driver , the size that is usually used to fix glasses or smaller.

First you need to lay a cloth down at a table . Lay the watch on top of cloth to prevent scratching . flip the watch upside down and have a good at the back of the watch bracelet.

If you look carefully you are going to see notches on the back of each link with an arrow pointing in. This is where the spring bars are accessible and can be pushed in to remove the link.

You need to place your spring bar remover, pin pusher or precision screw drive in the notch against the edge.

Mean while push the opposite side of the watch link up so you can see the most of the spring bar inside the notch.

The spring bar is going to look like a pink with a notch on the the top then gets smaller. As shown below on the left side of the picture. If you are looking at the notch on the spring bar, that is where you need to get our tool ontop of . So you can push down the spring bar.

Once you push down on that notch on the spring bar the link will be able to slip out . Without a spring bar remover it will be more difficult and you will need to be patient as you try to work your flat head screw driver into the notch and be able to push down . Once the pin is push down you need to pull the link from the rest of the bracelet.

Do not be surprised to take anywhere from 5 to 30 minutes if you have no experience and not have a spring bar remover.

Once you removed all the links you desire , You will need to put the spring bars back into the links and close the watch bracelet up.

The easiest way is to slip spring bar into middle of link. Bring the other end of the bracelet over so it the bottom covers the other link with the spring bar head out. Push the spring bar down with your tool as you slide the links back together.

The watch will set itself at specific time set times, this is likely to be at 0200 0400 and 0600.
You will however be required to set the time zone, the switch is likely to be on the back.
INFO:
Atomic Time Synchronisation:
How does it work.
SHORT VERSION:
Radio set clocks and watches receive a 60-kilohertz, radio signal from the NIST the official timekeeper for the US and is located in Boulder, Colorado. Ft. Collins. they use atomic clocks and transmits this official time via high frequency short-wave and low frequency AM radio signals, satellite transmission, Internet, and via telephone.

REFERANCE LINKS:
OFFICAL TIME:
http://www.time.gov/timezone.cgi?Eastern/d/-5/java
PHOTO OF ANTANA TRANSMITTERS:
http://tf.nist.gov/stations/wwvb.htm
R/
David
http://antiqueclock.clockstop.com/

Click on my profile (escapement), then click on Tips and Tricks. There you will find link to all CASIO watch manuals. Rate me, please

You can get instructions from the Casio web site.

Go to the casio web site "casio.com".

Select "support" and the "manuals", watches;

Accept terms

Select "watch manual archive"

Read the number of the back of your watch and enter it into the search box

Click on "search" and the download your instructions.

Click on my profile (escapement), then click on Tips and Tricks. There you will find link to all CASIO watch manuals.Rate me, please.

do a manual receive procedure
if you don't have the manual here's the procedure:
1-place the watch near the window (try to be on a clear area), the watch must be stable and the 12 o'clock side facing the window
2- press the D button for 2s untill the watch beeps
3- release the D button a message RC will be displayed
4-it take from 2 to 5 min to the signal to be acquired

hope it helps
give feed back

See page 3 of manual. It may help. User manual Casio G-Shock GX-56BB-1ER (English - 4 pages) QW-3221 (casio.com)

Time is not set correctly. You set the time as AM instead of PM and vice versa. Use the following manual to set time correctly. QW-5479 (casio.com)

Question edited for clarity. Question moved to Casio Watch, from Office Equipment. Pressure backs need a tool to unscrew the back and the gasket should be checked and greased. Best advice here https://www.fixya.com/support/r27181038-changing_watch_batteries ..

It is likely that the battery is depleted sufficiently that the sound feature can't work. Take it to a local jeweler for battery replacement service. https://www.fixya.com/support/r27181038-changing_watch_batteries ..

limited info generic answer if its the lower $ end units-- pop off the back --and remove internals careful of springs for buttons --check for debris -failed spring-button bi-metal fail /damaged

This is a job a specialist watch repairer should do. It will need specialist tools so if you are not familiar with working on watches pay someone to do it for you. Also consider the cost of repair. It might be cheaper to simply buy a new watch.

You need two SR1120 or type 391s.

It needs professional repair, before the seawater permanently damages the circuitry. Or you just buy a new one. https://www.google.com/search?q=Gold+Illuminator+A168WG-9W

Support ' Home - CASIO

https://world.casio.com > support G-SHOCK International Warranty Network. If you have any problems with your G-SHOCK, find out the nearest service center from this list. ‎Manuals · ‎Downloads · ‎About Authenticity Check · ‎FAQs

Parts and Repairs - US - Canada Authorized Service Centers

https://casiosupport.zendesk.com > en-us > articles > 56... Nov 28, 2022 - East Coast Service Location Casio Factory Service Center (All products) 570 Mt. Pleasant Ave.Dover, NJ 07801 ..

Setting the date on a Casio G-Shock watch can vary depending on the specific model you have. However, in general, you can follow these steps:

1. Make sure the watch is in timekeeping mode. Press the button at the 2 o'clock position to enter the timekeeping mode.
2. Press and hold down the button at the 4 o'clock position. This will activate the settings mode.
3. Use the button at the 2 o'clock position to navigate to the "Timekeeping" or "Time" setting. Press the button at the 4 o'clock position to select it.
4. Use the button at the 2 o'clock position to navigate to the "Adjust" or "Setting" option. Press the button at the 4 o'clock position to select it.
5. Use the button at the 2 o'clock position to navigate to the "Date" option. Press the button at the 4 o'clock position to select it.
6. Use the button at the 2 o'clock position to adjust the date. Press the button at the 4 o'clock position to confirm the date.
7. Press the button at the 4 o'clock position again to exit the settings mode. Your watch's date should now be set.

Note: If your watch model has different button configuration, please refer to the user manual for the specific instructions.

The battery compartment may not be making proper contact with the batteries. This can cause the batteries to drain quickly or not work at all. Make sure the batteries are properly seated in the compartment and that the terminals are making good contact with the batteries.
The watch may have a faulty component that is draining the batteries. This could include the display, processor, or other electronics in the watch. If the watch is under warranty, you can try contacting G-shock customer service for assistance.
The watch may have been damaged during the repair process. If the watch was mishandled or damaged during the repair, it could have caused a problem with the battery compartment or other components of the watch.
To troubleshoot the problem, you can try the following steps:
Check the battery compartment: Make sure the batteries are properly seated and making good contact with the terminals. Clean the terminals and the inside of the compartment with a soft cloth if necessary.
Check for faulty components: If the watch is under warranty, you can try contacting G-shock customer service for assistance. They may be able to help you diagnose and repair any faulty components.
Check for damage: Inspect the watch for any visible damage that may have occurred during the repair process. If you find any damage, you may need to take the watch to a different repair shop for further evaluation and repair.

Question edited for a little more clarity. This is one of those watched with multiple dials and dozens of functions. It sounds like there is an hourly repeating alarm at 10 minutes to the hour. All time zones are synchronised to the top of the hour. The best thing to do is remove the batteries for 2 minutes and replace them. Then set the time again. https://www.google.com/search?q=Casio+AE-1200whb-3bvdf+watch+manual ..

The issue you are describing with your Casio module 4722 watch in the HM (hand setting) mode sounds like a mechanical problem with the watch movement. It is possible that the gears or other internal components that control the movement of the hour and minute hands have become damaged or jammed. This problem could be caused by a variety of factors such as impact, moisture, or wear and tear. In order to fix this issue, it is best to take the watch to a qualified watch repair professional who can diagnose and repair the problem. They can determine if the problem is a minor one that can be fixed quickly or if a more extensive repair is needed. It's also a good idea to refer to the manufacturer's manual for troubleshooting steps and warranty information, as some issues may be covered under the warranty.

To adjust the dual time on your Tommy Hilfiger watch model 1791709, follow these steps:

1. Press the "Mode" button to enter the dual time mode. The dual time mode is indicated by the small "D" at the top of the display.
2. Hold down the "Adjust" button for a few seconds until the hours digit starts flashing.
3. Press the "Adjust" button repeatedly to adjust the hours of the second time zone.
4. Press the "Mode" button to move to the minutes digit, which will start flashing.
5. Press the "Adjust" button repeatedly to adjust the minutes of the second time zone.