20 Most Recent Golds Gym StrideTrainer 595 Elliptical - Page 7 Questions & Answers

The manual says you need to be able to lift 40 lbs safely to raise of lower the treadmill running platform, I I would guess twice that to physically lift it. The weight limit for a person using it is 250 lbs https://www.manualslib.com/manual/502826/Lifestyler-Expance-800.html#manual ..

Hi Tom, Hope so you're doing fine, cross tube is a structural element that connects the front and rear sections of the machine. If you need to change the axle bearings and remove the cross brace, you may require a specific tool known as an extractor. However, the availability of such an extractor and the specific procedure for removing the cross brace may vary depending on the manufacturer and model of the cross trainer. I recommend consulting the user manual or contacting Reebok customer support directly for detailed instructions on how to safely remove the cross brace and perform the necessary maintenance on your Reebok ZR9 cross trainer. They will be able to provide you with accurate information and guide you through the process. Hope so this will help you! Regards, Bryce June

Appears not, but there appears to be a pizo speaker, round thing, by the power cord. Place a piece of duct tape over it. It'll muffel it. Best to you

https://www.google.com/search?q=Aerofit+AF-737+TREADMILL+Error+Code+E01 ..

Parts suppliers in the link. This is not a North American brand. https://www.google.com/search?q=Aerofit+AF-737+TREADMILL+replacement+parts ..

It will be the same procedure as replacing the belt. They usually has a mechanism for tensioning the belt. That needs slackening off first. You could contact a seller, or watch the videos

Total Gym CycloTrainer for intese Cardio Workout

Total Gym Direct https://totalgymdirect.com > shop > total-gym-cyclotra... Easy Low-Impact Workout - simply lay back and cycle with the glideboard anchored at the bottom of the rails. Strengthen your core; .. US$399.95 · ‎In stock

• Total Gym CycloTrainer for intese Cardio Workout

  https://totalgymdirect.com > shop > total-gym-cyclotra... Boost your cardio workout with Cyclo Trainer for Total Gym! ... shavings from a rubber belt (presumably a belt that is used to increase the resistance?)

Amazon has them https://www.google.com/search?q=V-Max+MPE+Fitness+6380R+AC+Adapter ..

Here is there Support. Contact is at the bottom of the page.

Technogym Customer Support

Technogym https://support.technogym.com Technogym Customer Support is where you will find all the answers to your frequently asked questions, articles and useful resources to help you to get the ... I also found this A message stating 'the equipment is blocked' essentially means that a problem was detected that *might* be a blockage against moving of the moving parts. This commonly can be owing to two things: 1. the upper and lower assemblies (i.e the upper is the console, the lower is the electronics or boards in the lower part of the treadmill, e.g. the motor controller board and brake board) have a fault in the communication between them. This indicates first that you need to check the cable between console and lower assemblies, and also to re-seat either end, or at minimum make sure there is no breakage or crimping in that cable or wire harness, between console and lower assembly and lower boards. or 2. the error was detected by the brake board, and one must go through the error procedure for a brake board error. (In some models, (2) requires accessing the Low Kit Menu, to see whether there is a genuine error registered in the Low Kit Fault area of memory.) Also 3. you might unplug it from power while it is On, and see how that works, after about 2 hours unplugged, please. ..

limited info generic answer check motor and bearings for failing

In the link https://www.google.com/search?q=mosfet+IRFP+250N+IR+710P+4A+K9 ..

ck here.... https://www.manualslib.com/manual/907061/Technogym-Runrace.html?page=79 Best to you

It is a known issue with this unit. https://www.reddit.com/r/running/comments/i2ai1u/domyos_run_100_error_4_help/ https://www.google.com/search?q=Domyos+T900A+error+codes+E04

Hi, your machine might need maintenance. You can reach out to a Hobart service agent to get this maintenance done. I didn't see any error code associated with "missing link", you might check your device manual for this before calling the agent. Thank you.

https://www.google.com/search?q=stex+8020u+manual ..

The Laptop charger is giving reverse polarity. Use the correct charger for that machine (whatever it is). 'make model (what it is) in every question, first 3 words please. Google make model replacement charger https://www.google.com/search?q=%E2%80%8Bmake+model+replacement+charger ..