Euro-Pro Shark GI490 Iron - Answered Questions & Fixed issues

-Most likely time for New one. Good luck Mai

I would get a new iron. It is eight years old.

this iron has had it . it has rusted throuh the element and the rust s iron oxide . .. not repairable .. // replace it . as it will cost less .. mm

Pour all the water out of the iron, and fill it with white vinegar. Heat it and let it spit vinegar for a while. Chances are there is simply a bunch of crud in the iron from the water, most likely calcium carbonate. The vinegar is the cheap and easy fix, but if that does not do it you;ll have to bring out the "Big Gun" and use some "CLR" cleaner, available at most grocery or hardware stores. "CLR" stands for "Calcium, Lime and Rust", and a small jug of it is about $6 USD, It will clean the crud out for sure. Ironing seems to be a "lost art". Congratulations on being a smart desser!

A solution of white vinegar and water is a good cleaner for irons. Steam irons get clogged with mineral deposits, and vinegar works well to dissolve those deposits. Make a 50/50 solution of the vinegar and water and pour it in the iron, and place the iron on steam, allowing the solution to work thru the iron. You may have to do the cleaning a few times, depending on how clogged the iron is. For future reference, use distilled water in the iron, because distilled water does not contain any significant amount of minerals. Distilled water can be found in the supermarket in one gallon jugs.

Just get a new one you don't have to do all that.

change its metal heat plate .

More than likely your power cord has a broken wire. Plug the iron in and mover the cord around. See if you can find the broken wire. Typically where the cord comes out of the iron and right at the plug. Or replace the whole cord. Your local hardware store, youtube, or menards can show you how. Very easy to do. I tend to stay away from home depot.

What is a flush door, where is it used, and how is it constructed. Flush doors are commonly used in houses and security places.Metal flush doors are commonly used in higher security settings in motel construction where every guestroom can be accessible via an open-air catwalk.

In replacing the cord, you have to remove the screw that holds the back cover and unscrew the damaged cord from the heater terminal. Insert the new cord on the rubber insulator and screw it to the heater terminal.

the best way is to use the little screwdriver for to open with the help of some plier. Or use the tools for open the back light in car, is the same type .God bless you

there are 4 screws that you can see and two more under the large rubber stand off at the bottom. I also need you post the wire in the back because I took mine apart and now don't remember the position of the wires

see the diagrams . God bless you

the brown liquid is rust from leaving the water in the iron. Always dump the water out when you are done ironing. You need to run a descaler through it. you can purchase descaler online. The shutting off and on could be a loose wire.

Mine just did the same thing, I think the controller fried. There is aburnt smell coming from it

6 screws hold the cover on, 4 are visible, two are under bumpers on bottom. pry out the bumper.

Hi,Those types of problems are usually one of two things... the cord where is enters the iron, the wires are broken. Or the thermostat has gone bad...The iron will need to be taken apart and the wiring checked witha meter to find the problem for sure...heatman101

You'll have to remedy or better replace the cord. Just buy similar to hardware store and put it to your iron. It's simple to replace and you have to have a analog tester to be able to test the cord without plug-in to AC wall voltage.
Thanks for asking.

Here in fixya we do not sell or supply any replacing parts. Moreover in your case their is not any online shop that you can order online the button you need. Therefore your only chance to find the button you need is to find from the retail shop that you bought your iron the nearest repairing workshop where you can get the button you need.

on this and any iron that requires water use distill water it is free of minerals that way your iron is always clean and free of any sediment.