Top 20 Wareforce CG Underbar Glass Washer 208/230V Questions & Answers

Measure the temperature of the incoming water from your water source. Adjust water source temp to around 130 degrees, or what is required by data plate. http://www.webstaurantstore.com/documents/pdf/wareforce_cg_service_manual.pdf

Check you data plate. The inlet temperature must match the machine requirements, which means that your incoming water is too hot and the water heater temperature needs to be turned down. Here is a link to a installation/service manual. http://www.webstaurantstore.com/documents/pdf/wareforce_cg_service_manual.pdf

http://www.webstaurantstore.com/documents/pdf/wareforce_cg_service_manual.pdf Adjust incoming water temperature.

You need to ensure the incoming water temperature matches the requirements on the data plate, normally around 130 degrees. http://www.webstaurantstore.com/documents/pdf/wareforce_cg_service_manual.pdf

I am not sure they are available to non Hitachi service centres. https://documentation.hitachiaircon.com/glb/en/pac/rua-at3s

Cannot find the fault code . There are vidoes on u tube saying how to reset thr code By pressing the reset button . If this does not work youcan ccontact vaillent on there web page . I have a mate who works for them i will ask him as well

The P8 fault can mean many things when it pops up on your Mitsubishi Electric wall controller. The P8 fault is activated when the indoor coil sensor does not change the temperature for a set amount of time after the compressor is (or should be) switched on.

call plumber to replace gas valve, it may cheaper replace water heater. gas valve is not DIY

This one looks the same.https://www.ebay.ca/itm/133397559348They are made by Harper Wyman and using that model number, this is the result.https://www.google.com/search?q=Atwood+RV+oven+control+valve+57294But this shows more that looks similarhttps://www.google.com/search?q=Harper+Wyman+oven+control+valveAnd then if we go here and Zoom in, you will see MTZ 22300https://youngfartsrvparts.ca/products/used-atwood-wedgewood-oven-thermostat-57294Which leads us here and the Specs Sheet.https://www.copreci.com/en/gas-cooking/product-range/thermostats/with-safety-and-thermostatic-flow-regulation/372-mtz-22300-seriesand from there to here, and Parts Town stocks them!List Price: $ 318.24https://www.partstown.com/fagor-commercial/fgrc12008712..

test for sticking relay faulty circuit board or faulty stat

Beware when working with electrical equipment. It may cause electric shock. Check the power supply wires, connections with heating coils. If they are ok then possibly heating coils require replacement.

I would try their website; www.statewaterheaters.com They should show a list of their service agents.

You have to fix the root cause before you reset it. https://www.google.com/search?q=Clearflow+Bestway+Pool+Heater.+It+has+an+E6+error+code ..

Domestic Central Heating, Dodge Caravan, well pump or a Pool Heater, or something else. All questions need 'make model (what it is)' as first 3 words. With the exception of the Dodge Caravan, pumps have a small bleed screw. Google make model bleed pump or if it is an above ground well pump make model prime pump This is heavily weighted towards vehicles, but you will get the ideal of the power of Google! https://www.google.com/search?q=%E2%80%8Bmake+model+bleed+water+pump ..

Call for Service. The timer is fine, the boiler has failed. I presume it is gas fired, which means that only gas registered service techs can work on it.

The issue of the Paloma tankless water heater displaying error code C7 38 may be caused by several factors, including a problem with the thermistor or temperature sensor, an issue with the gas valve or gas pressure, or a malfunction with the control unit or circuit board. To troubleshoot, try checking the thermistor and temperature sensor, and verifying the proper functioning of the gas valve and gas pressure. If the problem persists, consider seeking professional repair or service.

The circuit is about to overload and the break could turn off due from too much electricity being used.The circuit is overloading or there is a problem with the panel needs to be replaced or the wires for your heater could be frayed or have tears in them and need to be replaced.

'make model (what it is)' in all question please Rick. All of the gas passageways in a fridge are very small. If you removed the gas valve and associated pipes, it takes a long time for the gas to bleed through and get from the gas line to the pilot light and that is needed to heat the thermocouple and allow the gas valve to open. It should also be mentioned that all work on Gas appliances should be undertaken by a qualified and registered gas technician.

https://www.electricfireplacesdirect.com/blogs/fireside-blog/7-reasons-your-electric-fireplace-may-not-be-working