20 Most Recent Jet Tech Systems F-14 - Multi-Purpose Ware Washer, Compact Counter " - Page 3 Questions & Answers

are you washing in pan mode? there are different modes

Dishwashers | Answered on May 09, 2019

I had the same error. Unplugged it. No help. What I did that fixed it was to hold the start/pause button down for 3 secs. This then started the machine's cycle where it had been before the error. In my case about 30secs before the actual end.

I think the eroor was caused by opening the machine before it had actually finished it's cycle.

Dishwashers | Answered on May 09, 2019

Every DW is a bit different. You have to pull it out of the cavity where it is installed. Turn off water and power first. remove the two screws at the top of the front face that anchor it to the counter. Remove the escutcheon at the bottom of the front . Typically there are two or four screws. Carefully pull it an inch or tow. Then look under with a flashlight and pull another few inches. Repeat until it is clear. Stop when you see the drain hose connection - I have owned back and front drainers. It is usually affixed with a clamp to the outlet. The other side goes to a drain of often the garbage disposer. Replace, reassemble. Good luck

Dishwashers | Answered on May 09, 2019

Your better off asking these people.


Dishwashers | Answered on May 04, 2019

You will need some skill with tools and knowledge of how your dishwasher operates. First, you will need to remove the back or front panel on the door. This will depend on the kind of dishwasher you have. When opened, look for a metal or plastic arm coming from the dispenser to a motor or gear. This is usually the problem and can be purchased from this site.

Dishwashers | Answered on May 02, 2019

check for clogged drain or pump failure

Dishwashers | Answered on May 01, 2019

No, too much water in the brine tank is NOT normal. The water level only be should 6-12 inches under normal settings. This may be caused be caused by an air link some where in the brine valve assembly or a loose connection. Check any drain line blockage or call Tampa Water Treatment Aquias for repair if you live in Florida.

Dishwashers | Answered on May 01, 2019

Always include the model number for best results. Check the top spray arm.
Make sure it rotates freely. That plays
a major roll in cleaning the top rack. Check for clogged holes in spray arm.
If your not using tablets fill both cups in dispenser. Make sure detergent is fresh and water is at least 125°F. Before starting dishwasher turn on the hot water on faucet till the cold water runs out. This makes a hot start in the beginning of cycle. Hope that helps!!

Dishwashers | Answered on Apr 29, 2019


Dishwashers | Answered on Apr 29, 2019

Hi Robin.
If the float gets stuck in the raised position, the dishwasher won't fill with water (Photo 3). Another likely cause is a clogged inlet screen or faulty inlet valve. ... If it doesn't, first make sure the float valve is operating freely (Photo 3). If this doesn't solve the problem, check the inlet valve and screen.

Dishwasher Repair Tips: Dishwasher Not Cleaning Dishes ' The ...

also try this link.


Dishwashers | Answered on Apr 28, 2019

Not finding what you are looking for?
Jet Tech Systems F-14 - Multi-Purpose Ware Washer, Compact Counter " Logo

1 questions posted

Ask a Question

Usually answered in minutes!

Top Jet Tech Systems Dishwashers Experts

Robert Marsolais
Robert Marsolais

Level 1 Expert

12 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Brad Brown

Level 3 Expert

18060 Answers

Are you a Jet Tech Systems Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Jet Tech Systems Dishwashers

  • Jet Tech Systems Dishwashers

Most Popular Question

part number f 14 dishwasher timer

  • Dishwashers