20 Most Recent
Jet Tech Systems F-18DP - Dishwasher, Undercounter, high temp. w/buil" - Page 5 Questions & Answers
Ariston dishwasher LFB 5B010 EX on/off, rinse aid and salt lights are flashing, left washing light orange and green (end) light on without flashing.
It sounds like there may be a problem with your Ariston dishwasher. The flashing lights and the dishwasher's inability to wash could be caused by a number of issues, including a problem with the control panel, a faulty water inlet valve, or a clogged wash pump.
To troubleshoot the issue, you can try the following steps:
- Check the control panel for any loose or damaged wires. If you find any loose or damaged wires, try to secure them or repair them as needed.
- Check the water inlet valve to make sure it is not clogged or faulty. The water inlet valve controls the flow of water into the dishwasher. If it is clogged or faulty, it could cause the dishwasher to stop working.
- Check the wash pump for any blockages. The wash pump is responsible for circulating the water during the wash cycle. If it is clogged, it could prevent the dishwasher from washing properly.
7/28/2023 8:00:37 PM •
Dishwashers
•
Answered
on Jul 28, 2023
Klarstein Dishwasher (Amazonia) when turned ON display cycles through the options, and buttons are unresponsive
If your Klarstein dishwasher is cycling through the display options and buttons are unresponsive, it is possible that there is an issue with the control board. Here are a few steps you can take to try and resolve the issue:
- Unplug the dishwasher from the power source for at least 5 minutes, then plug it back in and see if the issue persists.
- Check the dishwasher's circuit breaker or fuse box to make sure that power is being supplied to the unit.
- Inspect the control board for any visible signs of damage, such as burn marks or corrosion. If you find any damage, the control board may need to be replaced.
- If you are comfortable working with electronics, you can try resetting the control board by unplugging the dishwasher, removing the control board, and disconnecting the ribbon cables. Leave everything disconnected for a few minutes, then reassemble and reconnect everything.
If none of these steps resolve the issue, it may be necessary to contact a professional appliance repair service for further assistance.
7/26/2023 9:49:48 PM •
Dishwashers
•
Answered
on Jul 26, 2023
Dry light stays on all the time and dishwasher kitchen aid model kuds301xbl4 won't run
If the "Dry" light stays on all the time on your KitchenAid dishwasher model KUDS301XBL4 and the dishwasher won't run, there may be a few potential causes for this issue. Here are some troubleshooting steps you can take:
- Check the control panel: Inspect the control panel of the dishwasher for any buttons that may be stuck or not responding properly. Press each button to ensure they are engaging properly and not stuck in a pressed position. If you notice any issues with the control panel, it may need to be repaired or replaced.
- Reset the dishwasher: Turn off the dishwasher and unplug it from the power outlet. Leave it unplugged for a few minutes to allow any residual power to dissipate. Then, plug it back in and try turning it on again. This can help reset the dishwasher's control board and clear any temporary issues.
- Verify the door latch: Ensure that the dishwasher door is fully closed and securely latched. If the door is not closed properly, the dishwasher may not start. Check for any obstructions or debris around the door latch and clean it if necessary. If the latch is damaged or not functioning correctly, it may need to be repaired or replaced.
- Check the water supply: Confirm that the water supply to the dishwasher is turned on and there are no clogs or restrictions in the water inlet valve or hoses. Make sure the water pressure is sufficient for the dishwasher to operate properly.
- Examine the heating element: The "Dry" light staying on could indicate a problem with the dishwasher's heating element. Inspect the heating element for any visible signs of damage or malfunction. If the heating element is faulty, it may need to be replaced by contacting the manufacturer or an authorized service center.
- Contact customer support: If none of the above steps resolve the issue, it is recommended to contact KitchenAid customer support or an authorized service center for further assistance. Provide them with details about the problem and any troubleshooting steps you have already taken. They may be able to offer additional guidance or suggest further troubleshooting or repairs.
7/2/2023 2:11:34 PM •
Dishwashers
•
Answered
on Jul 02, 2023
Samsung DMT - 400 delicate light blinking
I know this is old, but I had the same thing happen to me (exactly as mentioned) and what worked was to replace the control panel. Fortunately, I had a spare I bought several years ago when I thought that was the problem to another issue which was solved without replacing the control panel. Instead of returning it, I kept it and it came in handy since it's either too pricey now or difficult to find. But that did it for me. I did everything to this dishwasher and already had a replacement picked out because nothing was working. Before doing getting a new one, I thought why if the issue was not the dishwasher. So I checked the hose and made sure no quinks or obstructions. I then checked for particles on the motor. Before that, I cleaned out the filters and replaced the check valve. I confirmed the motor was pushing out the water at a good pressure. Everything was fine. What turned out to be the problem was not anything to do with the drain but the control panel. I usually don't write comments, but I hope this helps someone.By the way, wrap your control panel chip with plastic and put cotton inside to absorb moisture. The plastic will prevent the condensation from ruining the panel chip. I know this because I replaced my first control panel due to condensation/moisture/steam - whatever you call it coming out of the dishwasher. After doing this, it lasted until the blinking delicate light which isn't due to moisture. I will never again buy a Samsung dishwasher or any of their kitchen appliances.
6/20/2023 7:22:57 PM •
Dishwashers
•
Answered
on Jun 20, 2023
How to reattach the door on SANSUI VCR?
To reattach the door on a SANSUI VCR, follow these steps:
1. Make sure the VCR is powered off and unplugged from the electrical outlet for safety.
2. Locate the door and check if any screws or fasteners are holding it in place. If there are screws, remove them using a suitable screwdriver. If there are clips or other fasteners, carefully release them to detach the door.
3. Inspect the door and the VCR chassis for any damage or broken parts. If any components are damaged, you may need to replace them before reattaching the door.
4. Align the door with the VCR chassis in the correct orientation. Take note of any guides or grooves that help position the door correctly.
5. Carefully slide the door into place, making sure it fits snugly and aligns with the rest of the VCR. Be gentle and avoid applying excessive force to prevent further damage.
6. If there were screws holding the door, reinsert and tighten them using the appropriate screwdriver. If there were clips or fasteners, secure them in their respective positions to hold the door in place.
7. Once the door is securely reattached, double-check that it opens and closes smoothly without any obstruction. Ensure that all buttons, controls, and features on the VCR can still be accessed and operated effectively.
8. Plug the VCR back into the power outlet and turn it on to verify that the door functions correctly and does not interfere with the VCR's operation.
If you encounter any difficulties during this process or if the door is damaged beyond repair, it's recommended to seek professional assistance from a qualified technician or contact SANSUI customer support for further guidance.
6/19/2023 9:29:34 AM •
Dishwashers
•
Answered
on Jun 19, 2023
My DD 603 has no power even though the power point has power I checked.
If your DD 603 dishwasher is not receiving power despite confirming that the power point has power, there could be a few potential causes for this issue. Here are some troubleshooting steps you can take:
- Check the power cord and connections: Ensure that the power cord is securely plugged into the power point and the dishwasher. Sometimes, the power cord can become loose or disconnected, resulting in a loss of power. Try unplugging and re-plugging the power cord to ensure a proper connection.
- Inspect the circuit breaker or fuse: Check the circuit breaker or fuse associated with the dishwasher's power supply. It's possible that the circuit breaker has tripped or the fuse has blown, cutting off power to the dishwasher. Reset the circuit breaker or replace the fuse if necessary.
- Test the power point: Although you mentioned that you checked the power point, it's still worth testing it with another electrical device to confirm that it is indeed providing power. Sometimes, power points can develop faults that may not be immediately apparent.
- Examine the control panel: Inspect the control panel of the dishwasher for any signs of damage, loose connections, or malfunctioning buttons. If there is a problem with the control panel, it may prevent the dishwasher from receiving power or displaying any signs of life.
- Consult the user manual or contact support: Refer to the user manual of your DD 603 dishwasher for specific troubleshooting steps and guidelines. If the issue persists, it is recommended to contact the manufacturer's customer support or a professional appliance technician for further assistance. They will be able to provide specific troubleshooting advice or arrange for a repair if needed.
Please note that working with electrical appliances can be hazardous, and if you are not familiar with electrical systems, it's best to seek professional help to avoid any safety risks.
6/18/2023 4:47:59 PM •
Dishwashers
•
Answered
on Jun 18, 2023
Not finding what you are looking for?