Top 20 Minn Kota Endura 30 Freshwater Transom Mount Trolling Motor Questions & Answers

Remedy? Get better equipment...

Hey Chris,, you are starting a project (or wanting to) that is going to be problematic... It will be easier to go buy a new trolling motor with the money you are going to spend attempting this conversion... the newer trolling motors are so much more efficient... Trolling Motors Fishing Motors Electric Boat Motors MotorGuide Trolling... https://www.minnkotamotors.com/

red goes on + black goes on -

Check EBay. I see prices ranging from $100 to $180.

http://www.ebay.com/itm/Humminbird-998c-HD-SI-Combo-408720-1-GPS-Chartplotter-Fishfinder-w-Transducer-/261296103349?pt=LH_DefaultDomain_0&hash=item3cd6761fb5

Yes but not for long. You need to buy a deep cycle battery. Regards Phil.

It depends on the Amp/Hour rating of the battery and the amount of current your motor draws on setting 1.

It is possible that the wires were reversed on the plate that holds the brushes. Since the motor is running backwards, the polarity is reversed and must be corrected for the motor to run correctly. I’m happy to help further over the phone at https://www.6ya.com/expert/jeremy_69f3cc28d95bf514

Lower drive unit seals? I need a model number to assist or the exact size of the seal if you know it.

I have an Endura 30 also and haven't been able to find an owner's manual or a service manual. I did find a schematic which is almost as good as a service manual. It gives an exploded view of the entire assembly as well as names and part numbers for each part. It's all I needed to order parts & repair mine. It is even done in such a way as to illustrate how it comes apart and goes together.

Here's the link: http://www.mikesreelrepair.com/schematics/displayimage.php?pos=-4777

I have an Endura 30 also and haven't been able to find an owner's manual or a service manual. I did find a schematic which is almost as good as a service manual. It gives an exploded view of the entire assembly as well as names and part numbers for each part. It's all I needed to order parts & repair mine. It is even done in such a way as to illustrate how it comes apart and goes together.

Here's the link: http://www.mikesreelrepair.com/schematics/displayimage.php?pos=-4777

here you go


http://www.amazon.com/MinnKota-Trolling-Motor-Power-Center/dp/B001PTHKMG/ref=pd_bxgy_sg_img_b

http://www.amazon.com/MinnKota-MK-105P-Portable-Battery-Charger/dp/B000MN8SEK

You will need a 100 to130 amp hour deep cycle marine battery. Check prices of many brands in your area. (WalMart, Autozone, boat dealers,ect.)

The Endura 40 is a 12V motor. To get off a bit cheaper go to a place that sells car batteries and get a sealed maintenance free battery.

I had the same problem tonight. I wound up getting it off by appling a diagional pressure to the prop. That held the shaft screw. Then my Dad turned the wing nut with a neddle nose pliars conter clockwise and it came right off.

My problem and probably yours too is once inside there is a pin holding the prop to the shaft that was broken. I don't know how to get the new pin back in since it is inside the prop with no access from the outside.

First is check for loose connections on cables and so on. Hopefully it is just a bad hookup. Loose wire, corrosion, nice easy stuff to find and fix.

If it just stopped and after that point you didn't see any life at all then I would think the controller board inside had failed. This controls or varies the speed of the motor. Unfortunetly thats going to be a shop job.

The good news is you should have a two year warrenty on that. So if you contact minnkota they should tell you where to drop it off to get fixed or replaced. The minnkota web page is www.minnkotamotors.com You can look at your warrenty and supoprt info from there.

and if you are in Ossian then the closest dealer they list is

united vaccuum
1011 e coliseum blvd
fort wayne
, IN
46805
Phone: 260-484-7162
[email protected]
10am-5:30pm m-f, 10am-5pm sat

That should get you fixed up.

Same problem. Bought motor used. Can't figure it out.

call 800 number on head minn kota they are very helpful and will fax, email or mail you anything you need.

the first thought for me is that things are heating up due to too much amperage being drawn by the motor or a loose connection.you will needs to check the specs on that motor to tell and need to know what normal readings are which minkota will gladly supply you.
but ..cause it happens to more than one ..it means that the switches you use..are not fit for the amperage this motor is working with ..Call the support (number is on the motor) ..and see what tip they recommend...

180 minute reserve trolling bat