20 Most Recent Arctic King MPG-08CRNI-BH9 8K BTU Portable Air Conditioner - Page 10 Questions & Answers

Usually an overheating problem. Check any vents on the back of it and vacuum them out. Make sure the fan is spinning freely. Full 'make model (what it is)' in all questions please, first 3 words. ..

Question edited for clarity.. Either the thermostat has failed or you are running it too hard like an air conditioner. https://www.google.com/search?q=polar+wind+MDL-65AEN1-BA8+freezing+up ..

Flashing Draft Fan Setting Indicator:Thisindicatesthatthestoveisinnormaloperationandthatthevacuumsensor detectsalossofpressureeitherbecausethedoorisopenorbecausethereisanegativepressureintheroomwith respecttotheexhaust.

E- MAIL there techs on there wed site they will know

first try changing battery

208 is 3 phase 240 volts is single phase. electrical wiring is best left to electrician. https://www.partstown.com/cm/resource-center/guides/gd2/turbochef-tornado-troubleshooting-fault-codes

Be careful when working on electrical devices without good knowledge. It may cause electric shock. There are two ways to fix it. First replace the switch with new one. If switch is not available, then any other good switch having the same rating may be affixed with little modification. Second bypass the switch and make direct connections and use wall socket switch to on/off the heater but this is not recommended practice.

Try this manual. It may help FEBO FLAME 17IN-42-118 USER MANUAL Pdf Download ' ManualsLib

Be careful when working on electrical devices. It may cause electric shock. First check the wiring and confirm all wires are in good condition. Then check connections are in proper order, not loose. Lastly check the fan itself. It may blown and require replacement.

sounds like you have bad flame sensor or the sensor is in a bad postition. To get eliminate the lockout turn the power off to the unit and back on again. Look at the circuit board light and see what the troubleshooting code is.

This manual may help you 11865379.pdf (lowes.com)

Let's go through some troubleshooting steps to help you resolve the issue: 1. Check the Manual: Start by consulting the user manual or the manufacturer's documentation for your specific furnace model. The manual may provide specific instructions for troubleshooting common issues and resetting the control unit. 2. Power Cycle: Try turning off the power to the furnace at the main electrical panel. Leave it off for a few minutes, then turn it back on. This power cycle can sometimes help reset the control unit and clear any temporary faults. 3. Check for Error Codes: The Beckett 7505 control unit may display error codes. Refer to the manual to identify the meaning of the blinking red light or any accompanying error codes. It can give you important information about the specific issue that needs to be resolved. 4. Check for Fuel Supply: Verify that the oil tank has an adequate supply of fuel. Low oil levels or a clogged fuel line can cause the furnace to malfunction. If the fuel level is low, arrange for an oil delivery. If the fuel line is clogged, it may need to be cleared or serviced by a professional. 5. Inspect for Blocked Air Intake or Exhaust: Ensure that the air intake and exhaust vents are clear of any obstructions, such as debris or ice. Blocked vents can prevent proper combustion and cause the furnace to shut down. 6. Reset Button: Some models have a reset button on the control unit. Locate the reset button and press it firmly to attempt a reset. If the light continues to blink after resetting, there may be an underlying issue that needs to be addressed. If none of these steps resolve the problem, it's recommended to contact a licensed heating technician or an authorized Beckett service provider. They have the expertise to diagnose and repair specific issues related to your furnace model. It's always best to leave complex furnace repairs to trained professionals for safety reasons and to ensure the proper functioning of the system.

Question edited for a lot more clarity. From the maker.

Fuel Conversion Kit NG to LP

Mr. Heater https://www.mrheater.com > fuel-conversion-kit-ng-to... Fuel Conversion kit for changing NPP overheads to LPP and from NG to LP. Kit includes all necessary labels and components required for the complete ... US$33.69

Mr. Heater ventless wall heater convert to LPG

The Garage Journal https://www.garagejournal.com > ... > Heating and A/C Mr Heater supports converting the Big Maxx 50 and 80 from NG to LP and sells a kit with the orifices for $25. https://www.mrheater.com/big-maxx-fuel- ... ..

Download the service manual from E2 Electric Furnace (nortekhvac.com)

https://www.pinterest.com/pin/best-of-e2eb015ha-wiring-diagram--426716133454752069/

Intertherm does not offer a wiring diagram for the E1 series anymore. So I have included a link to the E2 series. They are very similar and you may find this service manual helpful for whatever problem you may be having.

http://www.nordyne.com/literature/359a.pdf

What does the error code say

check thermocouple call richmond