Karcher 12" Upright Vacuum CV 300 12"- Standard Accessories Included - Answered Questions & Fixed issues
Karcher k5 full control- cannot remove hose from power washer
If twisting, pulling, and pushing are not working, then you may need to use some pliers to help loosen up the connection. You could also try wrapping the connection with a cloth or rag and applying pressure with a pair of pliers. If that still doesn't work, you may need to cut the connection and replace it with a new one.
10/31/2023 3:19:15 PM •
Karcher Vacuums
•
Answered
on Oct 31, 2023
•
40 views
Karcher W5 premium wet/ dry no suction but no blockage and filters are clean
- Blocked hose: Check the hose for any blockages or kinks that may be preventing air flow. If the hose is blocked, clear it out and try the vacuum again.
- Damaged impeller: The impeller is the component of the vacuum that creates the suction. If it's damaged or worn, it may not be able to generate enough suction. If this is the case, you'll need to replace the impeller.
- Damaged motor: If the motor is not functioning properly, it may not be able to generate enough suction. If this is the case, you'll need to replace the motor.
- Clogged or worn out turbine: The turbine is responsible for moving air through the vacuum. If it's clogged or worn out, it may not be able to generate enough suction. If this is the case, you'll need to replace the turbine.
- Broken or disconnected hose connection: Check the connections between the hose and the vacuum to make sure they are secure and not broken.
- Faulty switch: If the switch that turns the vacuum on and off is faulty, it may not be allowing the vacuum to run. If this is the case, you'll need to replace the switch.
2/11/2023 4:48:56 AM •
Karcher Vacuums
•
Answered
on Feb 11, 2023
•
141 views
Karcher puzzi 10/1 carpet & upholstery cleaning maching not working in suction mode.
It sounds like you are having some issues with your Karcher Puzzi 10/1 carpet and upholstery cleaning machine. Here are a few things you can try to troubleshoot the problem:
- Make sure that the hose is securely attached to the machine and that there are no kinks or blockages in the hose.
- Check the filter to make sure it is clean and not clogged. If the filter is dirty or clogged, it can reduce suction power.
- Check the solution tank to make sure it is properly seated and sealed. If the solution tank is not seated correctly, it can cause problems with suction.
- Make sure that the machine is turned on and that the switch is set to the "suction" mode.
- If the problem persists, you may need to take the machine to a Karcher service center for further diagnosis and repair.
I hope this helps! Let me know if you have any other questions.
1/4/2023 12:50:36 PM •
Karcher Vacuums
•
Answered
on Jan 04, 2023
•
157 views
T9/1
spinac on -of ist ok
11/9/2013 1:01:20 PM •
Karcher Vacuums
•
Answered
on Nov 09, 2013
•
95 views
No siphon action taken
Clean and check the vacuum motor for accumulated jam objects, dirt and dust. Use a small paint brush and if necessary apply some oil or grease in mechanical part. Be sure that the filter bag is clean also.Regularly clean it and you'll assure the vacuum will performed well.
Thanks for asking.
7/17/2011 10:20:27 AM •
Karcher Vacuums
•
Answered
on Jul 17, 2011
•
82 views
I have a K5.140 It
Most likely the hose pipe has nothing to do with the problem. Most likely is a loose connection and as time goes by the connection gets looser, which causes failure rate to increase. Once until is on, the power flowing through the loose connection helps keeps it connected. Open the unit and wiggle this and that until to can isolate the actual cause of the problem. Try not to shock yourself.
6/11/2011 2:31:40 PM •
Karcher Vacuums
•
Answered
on Jun 11, 2011
•
171 views
Cant get my soap dispenser
If you have not yet found a solution, then here are some steps to take.
1. The soap dispenser only works on low pressure!!!!!!! So you have to
REMOVE the high pressure Sprayer so that all you use is the Trigger
Gun without the Extender.
2. Pull out the thin Plastic Hose with the filter attached in the end, and insert into your container of detergent.
It will only splatter the detergent over the area you want to clean, so
you will then need to REATTACH the SPRAYER into the hand gun to work
with the soap to lather, clean and spray of till clean.
This seems to be the way the system works on this model......also known
as K2.36M (AU) in Australia or (EU) in Europe on the Karcher.com.au
site then Service then Manuals. or on the link below.
Hope this helps any of you who has misplaced their Owners Manual just
like I did and had a great problem trying to find a link as Karcher
doesn't recognize the Model No: as Winner 10 or 11.
Cheers, Luke
2/6/2011 12:36:31 PM •
Karcher Vacuums
•
Answered
on Feb 06, 2011
•
5,223 views
Bissell 1713 Crosswave Multi surface Cleaner. Why does the mesh on the water bottle lid keep coming off.
1. ENSURE THAT THE MESH IS CLEAN AND FREE FROM ANY DEBRIS OR OBSTRUCTIONS.
2. CAREFULLY REATTACH THE MESH TO THE WATER BOTTLE LID, ENSURING IT IS SECURELY IN PLACE.
3. AVOID APPLYING EXCESSIVE FORCE WHEN OPENING OR CLOSING THE LID TO PREVENT DAMAGE TO THE MESH.
4. IF THE ISSUE PERSISTS, CONSIDER CONTACTING BISSELL CUSTOMER SUPPORT FOR FURTHER ASSISTANCE OR A POSSIBLE REPLACEMENT PART.
3/28/2024 11:22:06 AM •
Vacuums
•
Answered
Yesterday
•
17 views
How to empty a etl vc-h3301 vacuum cleaner
How to open it to see if the fuse is blown. I removed the three screws I saw. I feel that there is another which prevents me from opening it in two. I looked under the tights, I removed the plate where the two buttons are located. I can't open it.
3/21/2024 4:57:04 PM •
Vacuums
•
Answered
on Mar 21, 2024
•
161 views
Not finding what you are looking for?