Top 20
Riccar Model RC1100 Canister Vacuum Cleaner Bags - Page 3 Questions & Answers
I can't reset my thermal reset button on my Riccar Brilliance
You may have hair and debris in the endcaps or bearings of your brushroll causing a restriction. The belt sensor thinks you have something stuck in the brushroll so it shuts it off. It's a simple fix, if you can't figure out how to do it take it to your Riccar dealer.
Power head on riccar canister vacuum doesn't turn onn
Either the cord is bad or the reset button has tripped. It could also be a bad hose or switch. Canisters are harder to diagnose because the electricity for the power nozzle runs from the canister to the power nozzle.
How do I change the fan in my riccar vacummn?
It depends on which model you have. Most models have a fan that will never need replaced. Tandem air and Supralight models have a fan that could be damaged on older models but is unlikely on newer models as fan are now made from a flexible material. Remove the motor assembly and disassemble to get to the fan. Remove the nut from. The shaft and remove the fan. Install new fan and put back together in reverse order as it was taken apart.
How do I change a riccar vacuum bag type z
Attach the bag securely in the bag holder. Slide the bag holder into the groove in the vacuum making sure the hole in the bag lines up with the hole in the vacuum where the hose attaches to.
How do I replace Riccar 8625 upper cord hook?
There are various small parts that make up the hook. First insert the L bolt through hole in handle. Put cord holder on L bolt, put lock washer and nut on and tighten nut. Then put cord hook on L bolt followed by spring, large washer, lock nut and another nut. Snug nut up and test to be sure it will swivel.
RICCAR 220 CANISTER VACCUM CLEANER POWER HEAD FALLS OFF OF WAND.
There is a little tab that releases when you push the pedal. The tab is probably worn and needs to be replaced. This repair is not hard to do when you know how but can be difficult if you've never done it. You can get the parts and advise from your local Riccar dealer
Burning smell when running
Filter is plugged maybe but burning smell is something over heating like a motor which should be serviced by a pro.
How to fix floor pedal on riccar 8850
Your 8850 is probably over 15 years old, almost all parts are interchangeable with the 8955 or 8925 model made today. You may need to replace the pedal if the catch has worn or broken. There is no wire on the. Pedal assembly but there is a spring that goes on the pedal shaft to make the pedal spring back after you push on it.
How to remove fan from rsl3c ?
Remove the bottom plate screws & bottom plate. Remove the screws holding the motor and fan assembly to the nozzle housing. Remove the screws Holding the fan housing to the motor to gain access to the fan. Remove the bolt holding the fan on the motor shaft to remove the fan.
Why does my riccar supralite vacuum makes a loud rattling noise like the roller is banging around?
You have something wrong with your brush roll or you have damaged the fan. Remove the brush roll and belt and turn the vacuum back on, if the noise is gone it is likely something wrong with your brush roll, if the noise persists you probably have a broken fan. You have to remove the motor and fan housing after removing the top cover, unscrew the bolt holding the fan on and install a new fan (you can get one from any Riccar or Simplicity vacuum dealer)
Where is riccar radiance filter reset button
Remove the bag door, you will see a little round rubber piece about 1/4 in diameter on the motor cover. Remove the rubber piece and very gently push the button while the brush roll motor is running
Riccar 8995 no suction
I think you mean it's an 8955, Riccar has not had a 8995 model. If there is no suction in the hose it has to have something clogging it. Open the little round opening on the back of the vacuum where the hose attaches to see if you have suction there.
Not finding what you are looking for?