20 Most Recent Frigidaire GLGF376DQ Free-Standing Gas Range with Self Clean Oven, Bisque, 5.0 Cu. Ft. Self-Cleaning Deep Sump Oven with Auto-Latch Safety Lock, UltraSoft Backguard Design, Upswept Cooktop, Ultra-Style Cast Iron Grates & Caps, Electronic Ignition GLGF376-DQ GLG - Page 2 Questions & Answers

do an online search for a shop in your area

Question edited for clarity. It is a little known issue. Probably needs to go back under warranty. https://www.google.com/search?q=hinari+steam+iron+digital+screen+not+working ..

Based on the issues you have described with your Phillips Perfect Care steam generator, it is possible that there may be multiple problems with the unit. It is difficult to say whether it is worth repairing without knowing the full extent of the damage and the cost of repair. The leaking water and green and blue lights could indicate a problem with the water tank or the steam generator unit itself. The fact that the electricity went off when you tried to clean it with descaler could indicate a problem with the electrical system. The whistling noise and lack of lights when you plug it in could indicate a problem with the power supply. If the cost of repairing the steam generator is significantly less than the cost of a new one and you have been satisfied with its performance in the past, then it may be worth repairing. However, if the cost of repair is close to or more than the cost of a new steam generator, it may be more cost-effective to purchase a new one. Ultimately, the decision to repair or replace your steam generator will depend on the severity of the damage and the cost of repair. It may be helpful to consult with a qualified technician to determine the best course of action.

How bad is this Scratch? Small light scratches will have no effect on what your ironing. Large, deep scratches are only a problem if they are over a steam jet hole. This can blow steam in the wrong direction which isn't safe. For bad scratches it is often better to replace the iron.

To replace the cord on an iron, you will need to:

1. Unplug the iron: Make sure the iron is unplugged and cooled down before attempting to replace the cord.
2. Remove the cord from the iron: Depending on the model of your iron, you may need to remove a cover or panel to access the cord. Look for any screws or clips that hold the cover in place and remove them using a screwdriver. Once the cover is removed, you should be able to see the cord and the connections to the iron.
3. Disconnect the cord: Use a pair of pliers or a wire stripper to carefully remove the wire connectors from the cord. Be sure to hold onto the wire connectors so you do not lose them.
4. Attach the new cord: Follow the steps above in reverse to attach the new cord to the iron. Strip the ends of the wires on the new cord and attach them to the wire connectors. Be sure to connect the wires according to the correct polarity (i.e., positive to positive, negative to negative).
5. Replace the cover: Once the new cord is attached, replace the cover and secure it with the screws or clips you removed earlier.
6. Test the iron: Plug in the iron and test it to make sure it is functioning properly.

If you are not comfortable or experienced in electrical repairs, it is recommended to have a professional perform the cord replacement. Tampering with the electrical components of an appliance can be dangerous and can cause damage to the appliance or injury to the user.

It sounds like your even-tempered iron is in a bad temper! I can think of no reason that you couldn't pull the plug from the wall socket. There is no iron of that model name, so I am puzzled by whole thing in your 'Anonymous' post. Disconnect the power at the breaker. Cut the wire with side cutters and throw the iron in the bin. Remove the wall socket from the wall and replace with a new one and throw that in the bin as well. Buy a new Rowenta next time. https://www.google.com/search?q=black+decker+even-tempered+iron ..

Error code 021 on a Turboion Croc Classic flat iron indicates a problem with the temperature sensor. This error can prevent the flat iron from heating up properly and may cause it to shut off unexpectedly. To fix this issue, you can try the following steps:

1. Turn off the flat iron and unplug it from the power outlet.
2. Use a small screwdriver to open the back cover of the flat iron and locate the temperature sensor.
3. Carefully inspect the temperature sensor for any signs of damage, such as bent or broken wires, loose connections, or burnt components.
4. If you notice any damage to the temperature sensor, you will need to replace it with a new one. You can purchase a replacement temperature sensor from Turboion or from a third-party supplier.
5. Once you have installed the new temperature sensor, reassemble the flat iron and plug it in. Turn it on and check if the error code 021 is still appearing.
6. If the error code persists, you may need to contact Turboion customer support for further assistance. They will be able to provide you with more detailed troubleshooting steps and help you resolve the issue.

I need to know how to pull the handle is in stuck posion

It will be a Security Screw Nancy. There are a few different types, Torx is the most common, but others have a triangular slot and are popular on domestic irons. You need a set of security screwdrivers or screwdriver bits. Or you can take the iron down to Home Depot and ask someone in the tool department.Tool to disassemble Black & Decker Digital Advantage Iron...

Hi, please lower the amount of water that you're putting into the iron by half and your problem should go away. You can also turn up the iron heat a little bit. Thank you.

Hi, Please wash the inside of the steamer with a mixture of 50% water and vinegar. You can use a brush to remove any mineral deposits. And if all else fails use heated water to pour into your device (you can double check this in your manual). Thank you.

Question edited for clarity. Question moved from Coffee Makers. One of the links says the lid must be raised. https://www.google.com/search?q=steam+press+KB-217B%2C+alarm ..

Idc really what's better only cuz as of right now this is what I have a gift from a friend who recently passed, I need the book instructions on how to put it together cuz for one I've never put one together & 2 I dont have the book. So if anyone knows where to go to find out how to put together &/or the pieces needed cuz all I've got for my kirschmann water home still is the main piece fitted with inside the I think copper circling tubing,the top n bottom pieces with nothing else. So can anyone point me in the correct direction please ?

Has it ever been descaled? https://www.google.com/search?q=ultra+XL+steam+not+getting+up+to+temperature ..

Regarding the Black & Decker Iron. You all talk about how to put water in the iron but none answer the question how to do that? What part do we remove or open to change or put in the water? Please answer this as soon as possible. This will also be on my Facebook to anyone there can you too help me?

I would try the manufacturers web site.

I have a genesis iron,it lights when it is on but does not become hot .it stays cold.What might be the problem?

Question edited for clarity, guessing your iron is a 'Rowenta' and not a 'Rowner'. You need a multimeter to test the element for continuity and the switch / thermostat for correct operation. It usually results in buying a new one. They are classed as disposable items when they fail. https://www.google.com/search?q=rowenta+dx9080+not+heating ..

It could be a faulty thermostat or faulty connection