Kaz 4100 Cool Mist Humidifier - 1gal - Page 7 - Answered Questions & Fixed issues

i don't know. consider using you vacuum to suck the filter clean. be safe. unplug your machine and use only the least amount of suction to do the job. don't make a hole in the filter. if you do, use a small piece of tape over the hole before turning on your unit.

try a different electrical outlet. turn it on and set it at highest reading then reduce the setting to the lowest. if still not running, unplug it and fiddle with the high level contact or switch on the bucket. seat the bucket properly then plug it back in to test if it works.

i don't know. please make sure your filter is clean. unplug your unit . gently shake giggle and move the float up and down. the switch for the float may not quite be making a firm contact.

i don't know. if moisture high, until resolved or repaired, consider using an electrical timer to shut it off and on for your choice of cycles.

i don't know. my unit has drain hose on bucket. if my bucket is not seated properly, it says my bucket is full. try to fiddle with the bucket high level float or similar.

Be careful. i do not know. set at highest setting and let it run. while running, reduce setting to the lowest over a few minutes. at a lower setting you should be able to tell that the compressor has started. run it for 5 minutes, then unplug your machine. next, feel the cooling coils to see if they are very cold. if they are not cold, your unit needs to be serviced.

no, this is not normal. air should be cooler. Be careful. i do not know. set at highest setting and let it run. while running, reduce setting to the lowest over a few minutes. at a lower setting you should be able to tell that the compressor has started. run it for 5 minutes, then unplug your machine. next, feel the cooling coils to see if they are very cold. if they are not cold, your unit needs to be serviced.

Be careful. i do not know. set at highest setting and let it run. while running, reduce setting to the lowest over a few minutes. at a lower setting you should be able to tell that the compressor has started. run it for 5 minutes, then unplug your machine. next, feel the cooling coils to see if they are very cold. if they are not cold, your unit needs to be serviced.

be careful. i do not know. set at highest setting and let it run. while running, reduce setting to the lowest over a few minutes. at a lower setting you should be able to tell that the compressor has started. let it run for 5 minutes, then unplug your machine. next, feel the cooling coils to see if they are very cold. if they are not cold, your unit needs to be serviced.

from earlier fixya..

Rich Landrum

• 4736 Answers

SOURCE:50 pt. dehumidifier will not Nothing worked, because the drain hole to the hose connection is clogged or the hose is clogged. When that happens, water is diverted to the bucket. Turn the Master ON/OFF Switch to OFF & Unplug the unit. Remove the hose and check it for clogs. If none are found, the clog is inside the hose connector. Using an 18" long plastic Zip Tie appropriately sized to fit the hole. Carefully insert the tip of the Zip Tie and continue to push it in, until you reach a bend in the tubing. You will have to gingerly work the Zip Tie past the bend, until it bottoms out or you run out of usable Zip Tie. Then slowly remove the Zip Tie while rotating (twisting) it. This will break up any clogs. As you reach the inserted end of the Zip Tie, be prepared as some water that might follow. Even if you don't see any residue from a clog, it may have been pushed out of the way. Reinstall everything, plug the unit in, turn the Master ON/OFF Switch to ON and take it for a test drive. Be sure the hose is no longer than 5 feet and that it gradually slopes down and away from the unit. The water drainage relies entirely on gravity.

E3 is a sensor error and some say cleaning the air intake filter can help. Others say the humidity sensor needs to be replaced.

No fuse. Probably fried the humidification switch. Need to replace as a start.

You posted in a dehumidifier forum. No one here will know about these loader issues. Perhaps re-post in another forum such as heavy equipment.

Could be about 15 years old. I don't know how long that model was offered for sale.

I got a 70qt (rerated to 40 qt if it is new) frigidaire well rated, very popular, on AMZ. of course your application will determine what you need

look in you manual. It is specific to models. or google it.

1: it isn't humid enough 2; it is running outside 40-95°F limits. 3. compressor isn't making the coils cold. It should be blowing warm air if it is working

usually, owners manual defines error codes. Otherwise google "(make, model) error codes". If it isn't blowing warm air, then the compressor isn't working which would be why it isn't making any water.

https://www.repairclinic.com/Shop-For-Parts/a14c9/Dehumidifier-Blower-Wheel-Fan-Blade-Parts https://www.manualslib.com/products/Garrison-043-6121-4-8670428.html