Kaz 4100 Cool Mist Humidifier - 1gal - Page 3 - Answered Questions & Fixed issues

Screws are normally hidden under the feet, under plastic plugs or under rounded screw covers. https://www.google.com/search?q=soleusair+hmt-d70eip-a+dehumidifier+leaks ..

It sounds like it needs servicing and recharging with refrigerant gas. It works by running the moist air over refrigerated elements where the moisture condenses and drips into the tank. Make sure you are on the right setting, most have 'blow air, remove moisture, and A/C'..

Page 18 of the manual says it is a 'parameter'. http://www.gullbergjansson.no/fileadmin/user_upload/Dokument/manualer/Avfuktare/Gullberg___Jansson_Manual_Avfuktare_till_inomhuspool_DP-serien.pdf Press CTRL+F and type 'C1' than press enter. There are 3 references to C1. ..

There are 6 rubber plugs in the top covering screws , 2 are all at hidden under the handle ends , the handle can be lifted to about 45 degrees and teased out an end at a time to gain access, the top then removes giving access to more screws which when removed along with screws under the bottom and inside the tank compartment allow the front and back to be removed for access

google MDK-65AEN1-BA9 manual they are readily available

normal it is an AC not dehumidifier. there is no humidity sensor, it operated on room temp not humidity. https://www.manualslib.com/manual/1015047/Challenge-414-0038.html#manual

sadly we have no service manual to find out .Check with Edison

see page 22 manual https://sps-support.honeywell.com/s/article/What-are-the-error-codes-in-an-E3-SA https://www.haierappliances.com/support/support-content/34659

Question moved from Larry's Computer forum to Dehumidifiers My dehumidifier no longer works https://translate.google.ca/?sl=auto&tl=en&text=My%20deshumidificater%20ne%20fonction%20plus&op=translate Take it to a refrigeration repair shop.

Check that the wee magnet hasn't fallen out of the float.

Impossible to diagnose without a full make and model, but likely a sensor issue. Your Google search query would be make model error code E9 https://www.google.com/search?q=dehumidifier+code+e9 ..

https://www.manualslib.com/manual/199712/Zenith-Zd309.html?page=15#manual

Clear the blockage and check the flow through the filter.

Had an issue with the water draining from the hose. Had worked before and stopped draining all of a sudden. Used a portable air compressor to blow it out. Went to the owners manual and saw that the drain outlet unscrews. Thought the drain hose was internal, taking the bucket off, then removing the drain outlet (2 screws, easy-peasy) Found the soft plastic drain line was kinked enough to stop/slow water from draining clearly. Plastic drain line needed to be heated with a heat gun/hair dryer with a metal file inside to restore the roundness of the tube. Keeping my fingers crossed.

If the dehumidfier is the right size then it would take a few days to week to get it down .

Not familiar with this brand but all of them are fundamentally the same. If you cleaned with water, make sure the unit is thoroughly dry. Especially electronic components. Also..Make sure that the float for the water tank is correctly installed and not jammed. Some manufacturers set a E2 code for water collection tank issues.

It's been 10 years trying to contact also and still nothing on this whirlpool Ad35usv unit. So might as well say that when they pro rate refund that you will get zero in return now for the few hundred spent to purchase

They don't sell any parts on this site . I woulld look for stockest on line or Key stone direct thye must have there own wed page

Assuming this is the A/C compressor, right? The compressor will be hot to the touch, the question is whether or not it is engagining when turned on, Check to see if the compressor clutch iis working by having someone turn it on and off while listebibg an observing the compressor clutch. Low refrigerant would or should orevent compressor operation to protect the compressorthrough a safety switch. Good luck

The pump may have simply failed.