Jules Jurgensen 5001YG ( ) : Swiss Quartz Movement Watch for Men - Answered Questions & Fixed issues
Where can i place an order for jj watch band (5001YG)
The only place you can get an original band for a watch is from the actual watch vendor. If its more then a few years old, it may even be discontinued.
Jules Jurgenson Corp
(610) 667-3500
101 W City Ave
Bala Cynwyd, PA 19004
Good luck.
I have a gold finish Jules Jurgensen ladies watch with a broken butterfly clasp,how can I get the clasp replaced?
Jules Jurgensen Watch Repair - Free Shipping & Estimate
AdĀ·www.watchrepairsusa.com/ Restoring Excellence To Your Watch. One Year Limited Warranty. Genuine Watch Mfr. Parts. Expert Craftsmanship. Free Insured Shipping. Services: Crystal Replacement, Watch Repairs & Service, Watch Restoration, Pocket Watch Restoration, Seals/Gaskets, Tune Up.
Common ServicesNo Problem Too Small
Tune Up, Overhaul, Battery & More
FAQsGeneral Questions
Shipping & Security
Jules Jurgensen Watch Repair, Overhaul/Movement, Crystal ...
https://www.totalwatchrepair.com > pages > jules-jurgen...
Maintained stock of Jules Jurgensen name parts ... Vintage Quartz Square Women'S Watch Black Band For Parts/Repair, #7730 Women'S Watch Clear Crystals ...
Do you replace batteries in
Yes you can replace batteries in wrist watches. And No we are not the company warranty indicated for service. Try contacting your local distributor to help with directions for service office.
Hope this solution has been helpful?
Looking to adjust the size
For removing or adding links firstly you will have to remove bracelet pins or screws. In case if there are screw on each side of bracelet - you have to use two screwdrivers simultaneously. In case if there are pins - read the rest:
You may or may not have arrows inside bracelet. Arrows are pointing the way the pins must come out. First you have to find out what sort of pins or even screws are used to keep links together (screw ends and pin end may look similar). Examine both bracelet sides and find the side where pin ends have a groove. Start with a tiny screwdriver and try to unscrew one. If it turns, but doesn't come out, that means you have a pins instead of screws. For removing pins the best would be pin removing tool (approx.5GBP on ebay), but it's possible to do the job without it. Take a hardened steel needle and blunt the sharp end to the approx. size of pin end diameter using any sharpening stone or sandpaper. Get an old towel and fold it to make a soft base for work (like small cusion). As you don't have a special bracelet holder you will need a pair of helping hands to hold the bracelet steady upright. You will need small hammer and pair of flat nose pliers as well. NOTE: The pins MUST be driven split end out first, not vice versa. Make sure that the grooved pin ends are facing towel, not the needle and hammer. Now place the watch on the folded towel, take that needle and smallest hammer you have and start driving the pin out using light blows. Do Not hit hard, as you will brake the needle, scratch your watch or even injure yourself. Watchmakers are using 45 gram hammer, so, calculate your strength of blows. After a few punches check if the split end is coming out and when you see that the pin end is coming out long enough - grab it with pliers and pull the pin out with pliers. When pulling, do NOT turn pliers, as pins tend to brake when twisted. Use firm grip and your strength to pull the pin without twisting. After shortening the bracelet or adding extra link(s) make sure that the pins go back EXACTLY the same way as they came out- the blunt end first in the hole and the split (grooved) end last. Before doing that check remaining pins in bracelet to make sure that you put them back from the right side of bracelet. It is recommended to use plastic hammer to drive pins back in or you will scratch or damage bracelet. If plastic hammer is not available use an old toothbrush handle (or some plastic item) as an absorber. Simply put pin into the hole as deep as you can with your fingers, put the toothbrush handle on split pin end and hit handle, not the pin. Make sure that pin ends are flush with bracelet. If needed- hit few more times. Job done! If you do not want to do it yourself, any jeweler will do it in a matter of few minutes.
Can i get a phone
mcdevito75 Here, I did a Fast Search and found a customer service number for Blue Dial a Jules Jurgensen Dealer, nothing on the main company though. Blue Dial may be able to help, it"s a toll free number, 1-877-518-9396 Hope this helps.
WHERE I CAN FIND A
Try this or they might be able to direct you further:
Is this your company?
Claim This Profile
Gold Cat Jewelry
19105 Kishwaukee Valley Road
Marengo,
IL 60152-9211 map
Phone:
(815) 715-6186
I thought the battery had
JJ do have a warranty but I do not know how long you have had your watch. Its always best to send your watch back to original vendor, especially on a more expensive watch. Any other repair done by outside sources can and will null and void the manuf. warranty. I would HIGHLY suggest the link below: The price is very resonable for the s/h.
http://www.jjwatch.com/watchRepair.asp
good luck
Hi there hope you can
All watches should arrive with battery fitted. As now there are too many variations of watch movements, it's impossible to tell exact battery code without seeing the watch. Nearest watch repair shop will be able to tell you that.
Not finding what you are looking for?