Top 20
Jamo E8 SUB Subwoofer Questions & Answers
I have Jamo E8sub need
hi,
the ic lm3886 should have voltage at its pin 1 and 5 , because it is the vdd supply pin of that ic. trace out, to where the track goes from pin 1and 5. it should go to the power supply or to any switching circuit. may be problem with its power supply side . any one of the voltage is missing. check the voltage regulators if there. check the power supply side i think complaint lies there. no need to replace the main board . from ur narration i think u have knowledge in electronics. make one more try to solve the problem.
ok
Pls help my jamo 210 sub does not swich on, where do i find the fuse
The manual doesn’t show a user replaceable fuse are you plugged into a house outlet or a power strip. If power strip confirm that power is present and try another slot to plug into. https://bcc2479de3c817356f4e-1bbe459354cb22c942d9efbc3d6dacbf.ssl.cf2.rackcdn.com/product-manuals/SUB210_OM.pdf
12/22/2018 4:16:37 PM •
Jamo Audio...
•
591 views • 0 helpful votes
Service center chennai
Does any other speakers work through the channels you are putting the subwoofer through? Reason i ask is could there be a fault with the channel you are using i.e AUX? is your subwoofer connected with Aux cables or is it a speaker cable? If aux cable is there a slight break in the cable? Have you checked the subwoofer for any faulty wiring although i would may be discard that idea as if it was faulty it would lose sound altogether. But still may be have a look to cross that off your list you never know. But to me i think you have a faulty channel or Aux connection/speaker connection on your amplifier/stereo.
1/6/2014 7:32:53 AM •
Jamo Audio...
•
109 views • 0 helpful votes
Jamo sub 660 wont come on
Hi,I have the Jamo sub 660 and it won't come on,I took it to my technician,and he told me that it has a broken ic,the broblem is that he cannot replace it cause the number on it is scratched,does anyone know what the number is pls! Thanks in advance Joseph
8/25/2012 6:48:35 AM •
Jamo Audio...
•
1,115 views • 0 helpful votes
My jamo d115 speaker tweeter distorts or rattels when any serious bass kicks in, how do you stop this?w
Possible this is a distortion from the Amplifier if the speakers are not damaged. however it is important to switch the speakers to confirm if the fault is relative to the particular channel in which case the amplifier is faulty. If not the speaker can be the culprit. All what is needed is to reduce the BASS level a bit lower when the volume is increased so as to allow the cross over to work. Also if teh cross- over network is faulty within the speaker the bass can vibrate on the tweeter.
12/1/2011 11:57:29 AM •
Jamo Audio...
•
635 views • 0 helpful votes
I have a Jamo AVR-693
This problem is from the main board, if you try to remove the cover of your unit you will see the main board try to check the solder parts of the pcb. for sure you will see loosed solder or cold solder specially the filter capacitor and the power transistor. If you see this loosed solder try to resolder it but be sure to unplug your unit before opening the cover. before replacing the amp. lets make some basic trouble shooting who knows you might fix it. Feel free to send feed back best regards.
7/17/2011 3:25:30 AM •
Jamo Audio...
•
535 views • 1 helpful votes
I have a Jamo surround
Since there are only two choices you could quickly try each of them. Or feed them both with the single LFE input and an RCA splitter.
4/17/2011 12:31:50 PM •
Jamo Audio...
•
345 views • 0 helpful votes
Not finding what you are looking for?