Top 20 Kipor Generator Diesel Kde5000ta Questions & Answers

Your question is general without specific details. Any one of many things will cause your generator engine to stop running. Is this question about a Kipor KDE5000TA? If so, your generator is powered by a diesel engine. There are safety shut downs built into the generator to protect the generator head and engine. Do you have any fault codes showing on your control panel display screen? (Trouble codes P-01 through P-05 will be displayed if there's a detected fault) If you have no fault codes, then you likely have a fuel problem. Do the obvious:

1. Visually check the fuel level in your tank. DO NOT rely on your fuel gauge. It may be stuck or otherwise not working.
2. If you have fuel, check your fuel filter. It may be clogged. If your fuel filter is good, you may have water contamination.
3. Drain your tank and refill with fresh #2 diesel fuel. I use "Diesel 911" with a biocide to prevent water contamination and bacteria growth in my fuel.
4. Make certain your fuel oil supply and return lines are clear, not leaking, and the fittings are tight.

I know I'm shotgunning, peppering the target. However, I don't have enough information to zero in on a specific area where the problem could be. Good luck!

Start with the obvious first. Remove and clean your battery terminals and wire connections. Before you reconnect the battery, check your battery voltage across the +/- terminals with a meter. It should read 12 to 12.6 VDC. If it reads less than 11 volts, replace the battery. If the battery is good and the battery connections are clean & tight, you may have a faulty starter or a starter relay.

Generator replacement brush notice: 1, from the model and material needs and the original brush. 2.It is best to grind the new brush to the Radian size of the old brush. 3. pay attention to adjust the brush grip pressure. 4. the carbon brush size should be equal, not too big or too small. The carbon brush is not subject to force in the process of placement. 5. pay attention to the carbon brush and armature to have obvious contact, do not push the carbon brush in. Generator brush replacement method: 1, the first with a special wrench loose brush braid fastening screws, loose fastening screws should not be loosened excessive, to prevent screw loosening and falling off. 2, take off the carbon brush braid, the carbon brush and the pressure-equalizing spring at the same time. When installing a carbon brush, put the brush into the brush grip. 3, then press the equalizing spring. 4.Use special wrench to fasten the brush and braid to fasten the screw. When fastening the screw, it is not necessary to exert too much force to prevent the screw from being damaged. 5. Check that the brush moves freely in the brush grip, and the spring can be pressed in the center of the brush.

Hope can say more details, so that i can provide a right methods. But if you want to see more faluts about diesel generator, here: https://www.dieselgeneratortech.com/generator-sets/discovery-and-elimination-of-faults-of-the-control-system.html

not being used that often you might need to clean the contacts in the solenoid and the starter

Question edited for clarity. No such word as 'propect'. Normally over speed, over voltage or a voltage leak in the generator windings. Contact the maker. https://www.google.com/search?q=Kipoor+KDE+12STA+-+Diesel+Generators.+L.H+Protect+light ..

https://www.manualslib.com/manual/844106/Kipor-Sinemaster-Ig2000.html#manual the schematic shows low oil switch there to kill spark dead.

The "undercharge" code on a Kipor KDE6700TA diesel generator typically indicates that the battery is not receiving enough charge from the generator's alternator. Here are some steps you can take to address the issue:

1. Check the battery: First, check the battery to make sure it is in good condition and fully charged. If the battery is old or damaged, it may not be able to hold a charge even if the alternator is working properly.
2. Check the alternator: Use a multimeter to check the alternator's output voltage. The alternator should be producing around 14 volts. If the voltage is lower than this, the alternator may be faulty and in need of repair or replacement.
3. Check the wiring: Make sure all wiring connections between the alternator, battery, and generator control unit are clean and tight. Loose or corroded connections can prevent the battery from receiving a full charge.
4. Check the voltage regulator: The voltage regulator is responsible for controlling the alternator's output voltage. If the regulator is faulty, it may be allowing too little voltage to reach the battery. Check the voltage regulator with a multimeter and replace it if necessary.
5. Check the fuses: Make sure all fuses in the generator's electrical system are in good condition and not blown. A blown fuse can prevent the alternator from charging the battery.

If you are not comfortable performing these steps yourself, it may be best to consult a professional technician to diagnose and repair the issue with your Kipor KDE6700TA diesel generator.

The overtemp light on the Kipor KDE6700TA diesel generator indicates that the engine is overheating. Here are some steps you can take to try to resolve the issue:

1. Turn off the generator immediately and let it cool down. Check the coolant level in the radiator and top it off if it is low. If the coolant level is consistently low, check for leaks in the coolant system and repair them.
2. Check the radiator fins for any blockages that may be preventing airflow. Clean the fins using compressed air or a soft brush.
3. Check the fan belt tension and replace the belt if it is worn or loose. A loose belt can cause the fan to rotate at a slower speed, reducing the cooling capacity of the radiator.
4. Check the thermostat to ensure that it is functioning correctly. If the thermostat is stuck in the closed position, it can cause the engine to overheat.
5. Check the water pump to ensure that it is working correctly. A faulty water pump can reduce the flow of coolant through the engine, causing it to overheat.
6. If you have tried all the above steps and the overtemp light is still on, it may be necessary to replace the thermostat, water pump, or other cooling system components. It's recommended to contact Kipor customer support or a qualified technician for further assistance.

Once you have resolved the issue, start the generator and let it run for a few minutes to ensure that it is operating at the correct temperature. Keep an eye on the overtemp light to ensure that it does not come back on.

not told what car or truck this is. moved yah.Kipor KDE45SS3 Diesel Generator 40 kVA?

The manual is here and there are videos in the first link https://www.google.com/search?q=KIPOR+KDE6700TA+GENERATOR Kipor K DE6700T Manuals - ManualsLib https://www.manualslib.com > ... > Inverter We have 1 Kipor K DE6700T manual available for free PDF download: Operation Manuals. Kipor K DE6700T Operation Manuals (23 pages). ..

When you load a generator it should increase in speed to compensate for the voltage drop, is it increasing in speed?

what make, year, model ?

Diesel engines do not need electrical supply to run. What do you mean.

Engines only need three things Fuel and air mixed Compression A spark at the right time One of those three is missing. Is your Caps Lock broken? Typing in all caps is considered shouting!

By performing the required maintenance

Guessing you do it the same as a car, by using a scan tool. https://www.google.com/search?q=Kipor+KDE45+SS3+generator+reset+the+%27service+due%27+& ..

notify manufacturer

The DC output for battery charging is from the engine alternator and is completely independent from the generator inverter.

As this is an inverter unit the typical polarization techniques for standard generators will not apply.

The ouput indicator being lit means the inverter input output should be good. This further implies a circuit disconnect state at the outlets. Try pressing the overload reset switch to make sure it is not in an odd state.