20 Most Recent Whirlpool Cabrio 7.0 Cu. Ft. Super Capacity Plus 7-Cycle Gas Dryer - White - Page 7 Questions & Answers

GO SEE A DEALER .

Electric dryer no start does nothing Check dryer Terminal block prongs both outside prongs should give combined 220, and 110 each if u check 1 outside & 1 center (ground) prong. Also check house electrical outlet for full voltage. CHECK THERMAL SHUT OFF THERMOSTAT USUALLY LOCATED ON THE BLOWER. for OHMS or resistance with a meter. Should show a closed circuit. Ohms WHEN THIS FUSE BLOWS IT WILL SHUT DOWN EVERYTHING. NEXT Test the PUSH start switch with meter for OHMS. Should show OHMS when pushed in or on start, and no ohms or infinity when in off position. If you hear a humming/clicking sound from motor area you more than likely have a bad motor. Try this test out to see if u have weak windings or relay/capacitor on motor. Open the dryer door and turn by hand the drum while machine is on ON position. And you or someone else presses the door engagement switch in. If it starts up then u have bad windings Another thing to check is the belt safety switch. With a multi meter. Especially if u just replaced the belt. The belt safety switch is attached to the Tensioner and motor. IT LOOKS LIKE A DOOR SWITCH SOMEWHAT a little black pc of plastic with 2 prongs going into it. Sits at bottom of motor. Under the Tensioner. Attach meter clips to the 2 prongs on switch, Then when the little white push button is pressed in it should show continuity and none when released. Lastly check ur DOOR SWITCH for continuity with a meter when the button is pushed in the (on/Door closed position,) it may have gone bad. https://www.youtube.com/watch?v=MhVUEhngZMg https://www.youtube.com/watch?v=9xD7lCXJ0ZM https://www.youtube.com/watch?v=sTRP6kHqAFs GOD IS GOOD !!!! WHICH IS WHY MY ADVICE IS FREE

VERY DANGEROUS YOU NEED TO CHNAGE OUT THE ELECTRICAL PLUG CORD AND CHECK THE TERMINAL BLOCK As u have a short somewhere its easy to change the terminal block

Electric dryer no start does nothing Check dryer Terminal block prongs both outside prongs should give combined 220, and 110 each if u check 1 outside & 1 center (ground) prong. Also check house electrical outlet for full voltage. CHECK THERMAL SHUT OFF THERMOSTAT USUALLY LOCATED ON THE BLOWER. for OHMS or resistance with a meter. Should show a closed circuit. Ohms WHEN THIS FUSE BLOWS IT WILL SHUT DOWN EVERYTHING. NEXT Test the PUSH start switch with meter for OHMS. Should show OHMS when pushed in or on start, and no ohms or infinity when in off position. If you hear a humming/clicking sound from motor area you more than likely have a bad motor. Try this test out to see if u have weak windings or relay/capacitor on motor. Open the dryer door and turn by hand the drum while machine is on ON position. And you or someone else presses the door engagement switch in. If it starts up then u have bad windings Another thing to check is the belt safety switch. With a multi meter. Especially if u just replaced the belt. The belt safety switch is attached to the Tensioner and motor. IT LOOKS LIKE A DOOR SWITCH SOMEWHAT a little black pc of plastic with 2 prongs going into it. Sits at bottom of motor. Under the Tensioner. Attach meter clips to the 2 prongs on switch, Then when the little white push button is pressed in it should show continuity and none when released. Lastly check ur DOOR SWITCH for continuity with a meter when the button is pushed in the (on/Door closed position,) it may have gone bad. https://www.youtube.com/watch?v=MhVUEhngZMg https://www.youtube.com/watch?v=9xD7lCXJ0ZM https://www.youtube.com/watch?v=sTRP6kHqAFs Hey GOD IS GOOD !!!! WHICH IS WHY MY ADVICE IS FREE

To determine the age of your Whirlpool dryer, subtract the current year from the year in which the dryer was manufactured

Either the door switch is faulty or it could be the start switch. Need to check out each component to find the one. Operate the door switch by hand to see if the light goes out when activated.
Eric

it could possibly be bad bearing in the drum support rollers in combination with lint build up

Dryer are pretty simple. The thing they need most is air flow. Remove the hose from the back, open the windows, and try a load of washing. If it works, airflow is the issue, blocked hose, turns to tight, vent not opening properly. Those are the three main reasons. If you google 'make model parts schematic', you may find that there are three or 4 heat regulating devices, cycling thermostat, high limit thermostat and thermal fuse being three common ones. https://www.partselect.ca/Whirlpool-Dryer-Thermostats.htm ..

suspect the door locking mechanism

So you have posted a washing machine model number and said you cleaned the dryer venting? That error is for the water level sensor.

Hi,

There can be many reasons why your dryer will not start or turn...

The most common causes are the belt breaking or jumping off, or the motor goingbad...

Here are a couple of tips that I wrote will help you to figure out why yourdryer will not run...

Dryer Repair - The Dryer is not Turning

Dryer Repair - The dryer will not start


heatman101

'';

Can only be a few things high temp fuse high limit thermostat failed element. VIDEO https://www.youtube.com/watch?v=fv2UqRUKnm0 Parts

Official Whirlpool Dryer Parts ' Order Today, Ships ... - PartSelect

www.partselect.com > Whirlpool-Dryer-Parts

The Dryer Thermal Fuse (Thermal Cutoff, Temperature Fuse) is a 2 by ½ inch, white, plastic safety mechanism that stops the flow of electricity to the motor circuit ...

Whirlpool - Dryer Parts - Appliance Parts - The Home Depot

www.homedepot.com > ... > Dryer Parts

Results 1 - 24 of 29 - Get free shipping on qualified Whirlpool Dryer Parts or Buy Online Pick Up in Store today ... WhirlpoolTop Load Washer/Dryer Cover in Gray.

Replacement Parts ' Whirlpool

www.whirlpool.ca > en_ca > services > replacement-parts

Our factory certified parts provide you with a promise only Whirlpool brand can make, that through our safe and genuine quality replacement parts, we will care ...

asd

motor was overheating need to replace

There are 4 Thermostats / Cut Outs / and high limit fuses in that machine. Test the old ones rather than just buying blind. There are videos showing how to test them with a multimeter. https://www.partselect.ca/Models/WED8200YW0/Sections/BULKHEAD-PARTS/?ModelID=1656403&ModelNum=WED8200YW0&mfgModelNum=&ManufactureID=3&Selected=3OPLX5EN&Position=1&mfg=Whirlpool&Type=Dryer&Mark=1 42 Thermostat, Internal-Bias (14)Part #: PS11746740 CAD$43.42 In StockAdd To Cart 43 Screw Part #: PS11742721 CAD$7.06 In StockAdd To Cart 44 HOUSING Part #: PS2372643 No Longer Available 45 DUCT-LINT Part #: PS11746341 CAD$112.94 In StockAdd To Cart 46 Housing, Slot Heater Box Part #: PS11746335 CAD$87.44 Special OrderAdd To Cart 47 Thermal Cut-Off with High Limit Thermostat (2)Part #: PS991443 CAD$66.05 In StockAdd To Cart 48 Thermostat (1)Part #: PS11746386 CAD$79.62 On OrderAdd To Cart 49 BRACKET Part #: PS990350 CAD$42.98 Special OrderAdd To Cart 50 Cover Part #: PS11746328 CAD$94.71 Special OrderAdd To Cart 51 Disposable Thermal Fuse - Two Terminal (5)Part #: PS11741444 CAD$29.84 In StockAdd To Cart ..

if voltage from switch to motor bad motor if no voltage possible bad switch or control board

Remove the attaching screws at the bottom and swing the cap up.

The sound comes from a tiny element on the control board. Its volume is fixed and can't be adjusted.

Doesn't make sense does it! The pipes and vents might be blocked at the back, but then it would get very hot and trip out on the hi limit thermostat.

Try manualsonline.