20 Most Recent Frigidaire Affinity 5.8 Cu. Ft. Electric Dryer - Page 8 Questions & Answers

Start simple. Check for the basic things that will not let the dryer run. Broken door switch. A loose wire on the door switch...those kinds of things. The same would apply to the start button. R

in don't know. perhaps the system resets itself. consider unplugging from electrical source. push start open and close.push stop if there is one to push. reconnect to power source.

AD is not an error code i found this out by goin to the frigidaire web site it just means that the dryer is in auto dry mode.

https://www.partselect.com/Models/FEQ1442ES1/#Symptoms click on the wiring link under the Manuals & Care Guides for FEQ1442ES1 and this will explain how to decipher the flashing lights.

The vent pipe is probably plugged up.

I would check the lint traps and exhaust line to make sure you don't have a restriction in air flow. the reduced air flow could cause the machine to over heat and will not allow it to run till cools down. I think I might also try different dryer setting on the timer just to make sure it is not the timer but sounds like something is getting to hot. http://www.appliance-repair-it.com/Frigidaire-dryer.html https://www.youtube.com/watch?v=S9KaJeV_bMQ https://www.youtube.com/watch?v=dg-vqyRgMPo https://www.youtube.com/watch?v=QQiZ8OFJINM https://homeguides.sfgate.com/troubleshoot-frigidaire-electric-clothes-dryer-80372.html https://www.youtube.com/watch?v=Qg1W9RrxXLY manual below https://www.searspartsdirect.com/manual/95gwascbq1-001428/frigidaire-ffre4120sw-dryer https://manualzz.com/manual/en/Frigidaire/FFRE4120SW/User%2Bmanual

Broken belt perhaps?

The code E68 indicates that a button is stuck. Check the buttons by pressing them one by one to find the stuck button.

The E9X codes all point to a faulty control board, as does the fact that the PF code canno tbe cleared. Just make sure none of the buttons are stuck down before you replace it...copied from another forum im in

Moisture sensor

Have you checked the belt maybe b broken

Request from Frigidaire

If you use fabric softener sheets in your dryer, they eventually will deposit enough residue in your lint trap to close up the mesh. Usually you cannot see the residue, although it is blocking the movement of air through it. My advise would be to remove the lint trap and run it under hot water and clean it well, then try the dryer with the clean lint trap. I hope this works for you and solves your problem.

Fifa M?nzen https://de.fifacoinszone.com Kaufen Fifa M?nzen https://de.fifacoinszone.com Kaufen Fifa M?nzen PS4 https://de.fifacoinszone.com/category-fifa19coins-ps4.html Kaufen Fifa M?nzen Xboxone https://de.fifacoinszone.com/category-fifa19coins-xboxone.html Kaufen Fifa M?nzen PC https://de.fifacoinszone.com/category-fifa19coins-pc.html Fut M?nzen https://de.fifacoinszone.com Fifa 19 M?nzen https://de.fifacoinszone.com/category-fifa19coins.html Kaufen Fifa 19 M?nzen https://de.fifacoinszone.com/category-fifa19coins.html G?nstige Fifa 19 M?nzen https://de.fifacoinszone.com/category-fifa19coins.html Fifa 19 ultimate team M?nzen https://de.fifacoinszone.com/category-fifa19coins.html Fifa 19 M?nzen PS4 https://de.fifacoinszone.com/category-fifa19coins-ps4.html Fifa 19 M?nzen Xboxone https://de.fifacoinszone.com/category-fifa19coins-xboxone.html Fifa 19 M?nzen PC https://de.fifacoinszone.com/category-fifa19coins-pc.html G?nstige Fifa M?nzen https://de.fifacoinszone.com

Check the owners manual or manufacturers website for error codes. Most likely cause...a bad control board.You tube will most likely have "how to replace" videos for your assistance. Good luck...

Typically there is a wiring diagram inside console area or on back of dryer.

That error is an E5b error. This indicates a problem with the heating element, the thermistor or the control board. You'll need to unplug the unit and access the wiring. Inspect the heating coil for breaks. Then test the voltage across the element (should see the line voltage) and check the resistance at the thermistor (should be ~50000 Ohms in a room temperature environment). If the above are okay, your control board is probably bad. If you post a comment with the model number, I may be able to point you the appropriate parts. If your dryer is under warranty, contact Frigidaire. I hope this helps. Cindy Wells

Searspartsdirect.com

Either it’s not latching properly or there’s a control board issue

Heating element or fuse / thermostat most likely bad.