20 Most Recent Insignia 32" 720p Flat-Panel LCD HDTV - Page 3 Questions & Answers

2 things have to happen. first, your tv has to be set for the correct resolution, second, You need to be recieving high def from your cable/sat provider.Your tv does not make programming high def, it allows high def.

adjust the display on settings...if doesn't works clear it is made by production....

Hello
Four digit universal remote code for Insignia TV are:-
0103 0189 0217 0135
................. 0133 0116 0167 0456 0029

Direct Code Entry

1. Press and hold the SETUP button until the red indicator stays on, then release the SETUP button.
2. Press and release the desired Mode button (TV, VCR, etc.). The red indicator blinks, then stays lit.
3. Enter the 4 digit code from the code tables. Note: after a valid code entry, the red indicator turns off. For an invalid code, the red indicator flashes.
4. With your device on, press CHANNEL UP. If the device responds, no further programming is required. Note: If some buttons do not operate your device, try one of the other codes for your brand.

[edit] Code Search If after trying "Direct Code Entry" your device does not respond, or if your brand is not listed, try doing a search of the code library for your code by following these steps.

1. Manually turn on the device (TV, VCR, etc.) to be controlled.
2. Press and hold the SETUP button until the red indicator stays on, then release the SETUP button.
3. Press and release the desired Mode button (TV, VCR, etc.). The red indicator blinks once, then stays on.
4. Press the CHANNEL UP button repeatedly (up to 300 times) until the device to be controlled changes channel. The red indicator blinks, then stays lit.
5. Press and release MUTE to install the code. The indicator light goes off.

Most users will want to store VCR codes under the VCR button, Cable codes under CBL, etc. If you want to store a VCR code under CBL, etc., first follow the procedure for Direct Code Entry and press CBL in step 2 of Direct Code Entry, then enter ANY VCR code in step 3 of Direct Code Entry. Then follow the steps above for Code Search.
OK.

it depends on what you are watching some things because it is only 720p are a higher or lower resolution you would need to either go to ur menu or use the zoom function to zoom in

if you have lines on either side of the picture it needs zoomed this is caused by 720p it is a half way resolution and i would not recomend it to anyone i would take 480i

hello marilyn stev!
you need to adjust resolution on your pc. right click on desktop and adjust screensettings to maximum. but your graficscard need to be a proper one which is providing necessary resolution for your tv.
feel free to contact me here under your topic for further assistance
regards

Used the VGA cable came with ur computer monitor,used that VGA cable plug in VGA input it the tv and plug it other end to the computer video card.Used ur tv remote look for a input button pushes look for the mode computer signal in the tv like input 1,2,3..so on.

Hi,

Thanks for asking FixYa for help. My name is Jeff and I will be assisting you today. You didn't specify the precise model, but choose your TV here abd you can get the manual.

http://insigniaproducts.com/productSearch.html?query=32%22&mode=manuals

And here there is information about codes:

http://insigniaproducts.com/support.html

If you are in need of additional help, please let us know.

Thank you for allowing us to help you today. Don't forget to vote. 4 thumbs up please.

Hello! If he's not getting a clear picture or a full picture he may need an HD receiver. If it's just not a full picture go through the tv menus and adjust the picture size you can call insignia as well their number is: 8774674289

Daniel Busa
DISH Network Customer Service

Hello!!!!!! To program your remote to your tv then your receiver is simple!!!! Follow these simple step in thelink below, and you will be good to go!!!!! Program your remote to your tv first ( step 6 and on), then program to your receiver (step 1-5). You will want to make sure that when you are programming the remote to your receiver, you will want to be in front of the receiver box. :) Hope this helps!!!


http://www.dishnetwork.com/SupportSection/remote-setup

Becki Barned
DISH Network Customer Service

There should be a "Zoom" button on your remote. Try looking near the top right corner (Bottom right button in the group of 9 rectangular buttons). Press that button and it should change aspect modes on your TV.

Confirm that you have the proper input selected -

check the remote and menu for format options. the remote may have a button that says "format" "size" "aspect" "wide" the tv menu will have an option to change the size in either the picture settings or something like that.

You can download from Insignia website:
http://insigniaproducts.com/support.html

hi,
there are no provision for connecting ipod. u can connect only usb mass storage devices through ur tvs usb. if ur ipod comes with an usb chord just connect it to the usb port of ur tv and then select usb. normally if tv has an ipod connectivity it will comes separate connection for the same, and there will be an ipod dock( optional accessory u have to purchase it separately ) .
ok

I had a similar problem with my Phillips 42 in. LCD HD TV.

Here's the problem. The Power Supply Board. I opened my TV up(warranty was up of course) and found several bad capacitors. Phillips and several other companies were sold capacitors that although were highly rated failed within 5 years because of a lack of preservatives. All sorts of electronic equipment is now being effected due to these defective capacitors.
Solutions?
1. Take it in and have it fixed
2. Open it up, check the board for faulty capacitors(bulged or leaking) Buy a new Power supply board and install it.
3. Remove PSB, remove faulty capacitors and replace with compatible new ones.

Hope this helps

Use the manual control buttons. If the channel your looking for isn't there by use the channel button then auto program the set again.

Look at th remote for 'format', 'zoom', or 'aspect' on the remote control.

Please see my basic troubleshooting guide here: http://www.fixya.com/support/r5093881-lcd_flat_panel_tv_troubleshooting_guide http://www.fixya.com/support/r6150077-basic_lcd_monitors_troubleshooting Failed TV and Monitors: http://s807.photobucket.com/albums/yy352/budm/ Learn about bad caps: http://en.wikipedia.org/wiki/Capacitor_plague Parts: www.shopjimmy.com Capacitors kit: http://lcdalternatives.auctivacommerce.com/Default.aspx he can make you a set of caps. Or www.digikey.com just make sure to use caps with low ESR, 105c, high ripple current, long life rating such as PANASONIC FM or FC series..

I have a RCA flat screen television and my dvd player when hooked up is in black and white. How would i fix this and if so plz be more specific then these other people.

try checking the menu setting on your Dish Network, there may be a television format in that menu set up, if it is only when a dvd player is playing, then check the format on that, so on so forth... that is one place to start, check if it is local (TV) or if it is from attached component ( Dish dvr/ dvd etc). also refer to your owner's manual.. if all else fails, call customer service @ insignia