The problem is the control panel, it is malfunctioning, you will need to replace it. Turn power to the oven off at your home's circuit breaker box. Remove the
three screws from the control panel with the crescent wrench. The
control panel is on the outside of the oven, above the door handle. Pull
the bottom of the control panel toward you, then lift it up. This
action will release the control panel cover's tabs. Identify the malfunctioning part. The mechanism that operates the door
latch during the self-cleaning cycle will be behind a smooth, square
plate held in place with two screws. White, black and red wires, as well
as a grounding wire, will be protruding from the face of the plate.
These wires will be twisted together with other control panel wiring and
covered with electrical wire caps.Remove the failed part by removing the caps and untwisting the wires.
Using the crescent or an appropriate wrench, extract any screws holding
the plate in place. The cylindrical-shaped mechanism will be attached to
and behind this plate. Visit a hardware store to acquire a
replacement part. To reassemble, slide the new mechanism into where the
old one was and reattach the plate with the screws. Reconnect the wires
by twisting them together and replacing the electrical wire caps. Replace the control panel by slipping the top of the panel into its groove and angling the panel downward. With this, it should function properly.
F0 Error indicates a bad control board and the control board
(electronic control) should be replaced to solve this issue. Hope this
helps...please post back for further assistance.
shut down the power to the machine,disconnect the touchpad ribbon,turn the power back on and let it sit for a day,if the code comes back you have a bad board,if it doesn't come back you have a bad touchpad
Your switch isnt right ,check the wiring on the switch or make sure the switch is closing or opening when its suppose to,you should hear a click each time it opens or closes. your problem is in the switch area no where else,the computer on the oven needs tosee that switch input and doesnt
These codes indicate an over temperature condition. The F2 & F3 error codes both mention the temp sensor. The temp sensor is mounted inside the oven cavity & regulates the oven set temperature. If the temp sensor fails the oven could overheat. This is what generates the error codes. I recommend having the temp sensor checked with an ohm meter, at room temperature the sensor should ohm out at approx 1100 ohms. If the sensor checks ok, then the control will need to be replaced.
Looking at this picture if you have already replaced part#16
which is the oven control then check the oven latch mechanism as if this part
goes bad the control will sense that the door is not closed and so the fan won't
run resulting in the oven not turning on. Hope this helps...please post back
for further assistance.
It's no fault code for F1 mwans the clock timer is inoperative You can send the clock to CGI Limited in Illinois for repair call 866 737 2244 or go to www.cgiltd.com for further info. This will probably cost 150-200,be sure before you invest that much that it is worth the expense.
I'm sorry that you haven't received an answer yet.
The response rate on FixYa FREE questions is usually over 80%, but sometimes questions go un-answered when: 1. the question is unclear, incomplete, or poorly worded... 2. the question is mis-categorized - so the correct experts aren't viewing it... 3. the question requires an answer for something that cannot be explained online adequately... 4. specific training, tools, or equipment are required to avoid injury or death... 5. the Experts that are online simply don't have the resources to answer your question fully...
Please feel free to re-work your question if you feel one of these may be the reason. Of course you are not required - but converting your question to a PAID one usually increases the reply rate as well.
Normal rates for FixYa are... $ 9.99 answer for one question. $12.99 Live Real-Time online chat or premium e-mail support. $29.99 Live Real Time phone support Sometimes FixYa will run specials for unlimited questions via monthly subscription or reduced rates for limited periods.
Consider the savings that can be had when an informed Expert can save you a $100 service call, or a $350 trip to the car dealership. Your problem solved - guaranteed! Or your money back!!
If you don't want to pay - feel free to re-submit your question so it returns back to the top of the work queue if you still need help.
Thanks for using FixYa - a 4 THUMBS rating is appreciated for helping with your FREE question
One of your "switches" to your burners is shorting causing unit to spark when in the off mode, or, you may have a bug problem, bugs have made their way into the spark module.
1: if no bug problem, disconnect stove from electricity, lift top up, remove all of the single connections to each switch to top burners(make sure they don't have any bare wires touching the frame), then plug unit back in, if still sparking then replace module.
If you dont see it around the door or inside the stove you'll have to raise the top and it should be there somewhere. The part number for the glass top I can get for you if I have the model number
Question edited for clarity.
The bake element failed? Test for continuity.
If it has a fan, test that too.
If it is electronic, check the thermistor temperature sensor.
For suspected control panels or mainboards, I always suggest dealer service so you get the correct diagnosis and warranty on the parts and the job. They are also expensive.
..
Most modern appliances like cookers and washing machines have the control panels and displays are fitted from behind the front panel, inside the machine. You will be better off getting a professional repairer to do it for you. *Remember* this is a Gas appliance that you're working on so BE CAREFUL. You might have to remove several other panels to get to the touch pad so if your going to do it yourself turn OFF the main gas supply first then make notes and take photos as you go.
No reset found in the manual. You can try this and hope it works..
Turn off the circut Breaker to the stove for 5 minutes to see if it resets. Checking around the net I've only found
"Item Discontinued"
The part is no longer sold by the manufacturer.
The manufacturer does not stock any substitute parts to replace this one and therefore, unfortunately, we cannot obtain or recommend a substitution for this part.
We cannot obtain the part through any other means.
