20 Most Recent
Dacor ECS127 Epicure Stainless Steel Electric Single Oven - Page 9 Questions & Answers
Dacor Preference RSD30 Gas Range My wife put the
I don't see the make and model number of your unit. I only see part of your post. Please post the make and model number. It should be a simple fix. From what I do see in your post, it sounds like the control board will need to be replaced.Regards,Richard
10/18/2011 3:17:55 AM •
Dacor Ovens
•
Answered
on Oct 18, 2011
Model cps130s selection of oven
Hello,
There have been numerous oven control systems used over the years. The following instructions describe various methods that might be employed to correct such a condition.
In almost all cases if the temperature reading is more than 35°F out, some part of the control system will need to be repaired. Usually adjustment will not provide an adequate solution to the condition and may even make it worse.
Before attempting any kind of adjustment on a hydraulic oven control, make sure the thermostat's sensor bulb is properly mounted in the oven cavity and not touching the oven wall or metal rack. The sensor bulbs are held about 1/2" away from the oven wall by a small metal clip.
Dial type control
Some models have the calibration adjustment on the underside of the knob itself. On this type of arrangement, the loosening of the dial plate and moving it one way or the other will change the temperature reading on the dial once reinstalled.
Other control designs have the temperature calibration screw down the center of the shaft. These usually require a special small screwdriver to access it. See below for a link to a detailed calibration method for one brand of oven thermostat.
Electronic Control Calibration
The following procedures are designed to provide an general idea how calibration adjustment of the oven temperature display on many electronically controlled (ERC/EOC) ranges and ovens is done. The actual procedures vary from model to model so check your owner's manual.
If the temperature is out more than 35°F, the oven sensor or the electronic control may need to be replaced to correct the inaccuracy.
General
Press BAKE
Select a temperature of 550
Quickly (within 5-seconds of setting 550) press and hold the BAKE button approximately 5-15† seconds until "00" or the previously entered temperature adjustment is displayed.
†Pressing longer could cause an F0, F1 or F7 error to be displayed.
Press the UP/DOWN arrow button or turn the set knob to change the oven temperature in 5° increments to a maximum of +/- 35°
Press the CLEAR or OFF button to return to normal operation.
Hoping this will help to solve the problem....
9/24/2011 12:13:58 AM •
Dacor Ovens
•
Answered
on Sep 24, 2011
H E L P
Hello.
Please apply the solution this way!
To
close an oven door when it's in the locked position and the door is
open, press and hold the oven door light switch while following these
simple steps:
- Program the oven to self-clean.
- Wait 20 seconds.
- Cancel self-clean.
- Wait 20 seconds.
To self-clean your wall oven, follow these simple steps:
- Remove the oven racks.
- Set your oven control to "Clean."
- Select a cleaning time or choose a cleaning level:
light, medium or heavy. For typical cleaning needs, we recommend that
you select a cleaning time of three hours or choose the medium setting.
- Select "Start." (To set a delayed start, see your Use & Care Guide.)
Note: For safety reasons, the oven door will remain locked until
the oven cools down. When it is sufficiently cool, the door will
automatically unlock.
Thanks for using fixya.
9/7/2011 1:20:43 AM •
Dacor Ovens
•
Answered
on Sep 07, 2011
The oven is locked. What
Hello, Thank You for using FixYa. I will be helping you today.Try to unplug the unit or shut off the breaker for a minute and see if it unlocks
Thank You and please ACCEPT my answer and Rate my answer if it was helpful..
7/7/2011 6:20:21 PM •
Dacor Ovens
•
Answered
on Jul 07, 2011
Dacor oven display showing F0
The
"F0" error code description is a stock function key. Here are basic
test that will help you to determine if the ERC or touchpad is
defective.
1. Unplug the range power cord or turn the power off to the range at the circuit breaker.
2. Gain access inside the control panel.
3. Disconnect the touch pad (also called keypad or membrane switch) ribbon from the ERC.
4.
Make sure there are no lose wires, or anything else that may cause a
short when power is turned back on. Assemble the control panel back the
way it was.
5. Turn the power back on.
6. Wait for at least one hour to see if the code comes back.
7. If F0 comes back, replace the ERC. If it does not, replace the touch pad.
Hope it helps.
Thank you for using FixYa.
6/14/2011 9:38:33 PM •
Dacor Ovens
•
Answered
on Jun 14, 2011
Model cpd227s date 9405
Hello,
the ERC of your oven has failed. Often they encounter a
glitch.
Here is what you should do first; try turning the breaker off for several minutes, turn it back on then try again.
If turning of the breaker for some minutes doesn't solve the problem, please let me know so that I may direct you further on what next to do.
Regards.
5/17/2011 12:28:32 AM •
Dacor Ovens
•
Answered
on May 17, 2011
On cleaning setting it just
Hello &
Welcome to FixYa
Error code F8
is displayed due to failure of door latch motor and usually ocs when the motor
runs for two minutes without the door locking in the self-clean mode. Replacing
the door latch-lock motor is recommended repair. Please get back to me if you
have any other questions.
Kevin
3/6/2011 7:22:23 PM •
Dacor Ovens
•
Answered
on Mar 06, 2011
We have a dacor double
Hello & Welcome to FixYa
Error code F1 is displayed due to electronic oven control failure and the only way to solve this problem is by replacing the control board which is bad. Please get back to me if you have any other questions.
Kevin
2/3/2011 8:28:49 PM •
Dacor Ovens
•
Answered
on Feb 03, 2011
The oven control lights come
STOP.
I suggest you to check the fuse box and shut off the circuit break that label for the kitchen stove or kitchen.
This will give you some assurance and time to troubleshoot the oven problem.
===
Please reply with MAKE AND MODEL # on reply.
===
I can only give you general fix and check list until you provide the exact model.
Beside the oven light,is there any non-function part in your range?
GAS or ELECTRIC?
=======
For electric stove.
Make sure the electricity supply is off.
Most dial can be pull directly off (outward)
Please give it a gentle tug and see can the oven control dial move outward.
The objective is to clean the dial on the body of the stove.
Please use plastic glove and mild detergent to wipe the post on the dial clean.
Use dry towel to COMPLETELY dry off the post of the oven dial.
Let it dry for 30 minutes or use a fan / oven hood range to speed up the drying process.
Place the dial back on.
Turn the circuit breaker back on and test the oven.
============
Gas oven will need the same cleaning instruction.
The igniter can be worn.
This can be accomplish easily.
I will wait for you reply on the exact model.
1/27/2011 6:09:50 PM •
Dacor Ovens
•
Answered
on Jan 27, 2011
My dacor oven light won't
Sorry to read about your problem, I hope this helps you out.
you have a defective door switch
I tried to help you. Please help me and Rate/Vote on my response. We take the time to answer your question. take the time to rate us.Thanks and good luck
1/12/2011 8:10:50 AM •
Dacor Ovens
•
Answered
on Jan 12, 2011
After oven turn on
F1 means the system watchdog cicuit has detected a fault.
Try pressing CANCEL for 30 seconds if it continues after that you will probably need a replacement control board.
12/13/2010 2:54:21 PM •
Dacor Ovens
•
Answered
on Dec 13, 2010
Not finding what you are looking for?