Dacor ECS127 Epicure Electric Single Oven - Answered Questions & Fixed issues
What does "PRB 400 (degrees)"
Hi,
PRB stands for Power relay board.
This is a bad error. This means that the power supply board had failed and needs replacement. The cost of replacement would be anywhere between $150 to $300.Unfortunately, this is not a DIY. You need to call a tech on site to replace the same.
Let me know,if needed further assistance.
Hope i helped you.
Thanks for using ' Fixya ' and have a nice day!!
11/26/2010 12:17:11 AM •
Dacor ECS127...
•
Answered
on Nov 26, 2010
•
146 views
What does the F1 mean
Hi, the F1 error code means a problem with the System Watchdog Circuit..
Press "Cancel", if beeping continues after 30 seconds, replace the main control board (also called clock or ERC).
11/17/2010 2:12:24 PM •
Dacor ECS127...
•
Answered
on Nov 17, 2010
•
512 views
Heating element won't heat.
Checked breaker,
Hi,
It gets tricky from there...
I would check for power at the element....if there is power and the element is not getting hot then you have a bad element.... 220 volts across the two wires to the element or more is considered proper power...
If there is no power there.... then you need to flow the wires back till you get power and that is where your problem is....
This is the best way to troubleshoot your oven...but a good quality electrical meter is needed.... and you need to be very careful when working with electric as it can kill you!!!
heatman101
11/7/2010 3:59:39 AM •
Dacor ECS127...
•
Answered
on Nov 07, 2010
•
83 views
Dacor error codes
HI. the F-1 code is a System Watchdog Circuit failure code.
Press "Cancel", if beeping continues after 30 seconds, replace the main control board (also called clock or ERC).
Concerning the F-5 code. This is an oven temp sensor failure code. have it replaced asap. ((Check the wiring leading to and from the control and sensor for cracks and fouled structure. if the wiring is bad, replace the harness as well)),
11/22/2011 9:26:08 PM •
Dacor ECS127...
•
Answered
on Nov 22, 2011
•
3,520 views
I don't know how to clean the oven
You should have a function switch that says " self clean ". Normally, all you have to do is turn the control on to "self clean" and let the oven do the rest. It will take about 3 hours or so to complete the cycle.
1/30/2009 11:14:29 PM •
Dacor ECS127...
•
Answered
on Jan 30, 2009
•
305 views
Oven not heating
i have had this problem twice. once was the heating element actually had shorted out because the little ceramic holders had broken, this necessitated getting new element. can be checked out with an ohmmeter by yourself or by taking element into appliance repair place. the other time, it was that the manual reset switch had tripped after a self-clean cycle. actually at the moment, that has happened again- design flaw perhaps in the RSD30 range?
so anyone who can tell a reasonable competent refrigeration/HVAC technician where the manual reset switch is would be appreciated.
6/24/2008 10:07:37 PM •
Dacor ECS127...
•
Answered
on Jun 24, 2008
•
417 views
Dacor model W305 oven element will not turn off
If the element in your Dacor W305 oven will not turn off, there are a few things you can try:
- Turn off the power to the oven by unplugging it or switching off the circuit breaker. Wait a few minutes and then turn the power back on to see if the element has reset.
- Check the oven's temperature sensor. If the sensor is faulty, it may be sending the wrong signal to the oven's control board, which can cause the element to stay on. You can test the sensor with a multimeter to see if it's functioning properly.
- Check the oven's control board. If the control board is faulty, it may be sending a continuous signal to the element to stay on. You may need to replace the control board if this is the case.
- If the element is physically damaged, it may be causing a short circuit that keeps it on. In this case, you will need to replace the element.
If none of these solutions work, it may be best to contact a professional technician to diagnose and repair the issue.
2/27/2023 5:33:55 PM •
Dacor Ovens
•
Answered
on Feb 27, 2023
•
35 views
Have Dacor wall oven ECS130SBK . The time is correct but to the right it says OFF in red. How do I fix it?
If your Dacor wall oven displays "OFF" in red, it means that the oven is not turned on or is in standby mode. To turn on the oven, follow these steps:
- Press the "Bake" or "Convection Bake" button.
- Use the "+" and "-" buttons to set the desired temperature.
- Press the "Start" button to begin preheating the oven.
If the oven still displays "OFF" after following these steps, try turning the power to the oven off for a few minutes and then turning it back on. If the issue persists, there may be a problem with the oven's control board or wiring and you may need to contact a qualified appliance repair technician for further assistance.
2/26/2023 10:36:24 AM •
Dacor Ovens
•
Answered
on Feb 26, 2023
•
65 views
Dacor Epicure Dual Fuel Range ERD36SACH/LP The oven only heats in pure covection.
f resetting the high temp limit switches did not resolve the issue, it may be a problem with the broiler and bake elements themselves or with the wiring and connections that supply power to them. It would be best to have a qualified technician inspect and diagnose the issue to determine the necessary repairs.
2/14/2023 5:50:56 AM •
Dacor Ovens
•
Answered
on Feb 14, 2023
•
56 views
Dacor up button not working
Try a spray of switch and contact cleaner spray with the power turned off. Get behind the buttons if possible.
1/17/2023 11:22:53 PM •
Dacor Ovens
•
Answered
on Jan 17, 2023
•
93 views
Dacor double oven model ECD227SCH relay board preventing oven from working......
It sounds like you may be having an issue with your Dacor double oven. If the relay board is preventing the oven from working, there could be a problem with the board itself or with a component it controls.
To troubleshoot this issue, you may want to try the following steps:
- Check the oven's electrical connection and circuit breaker. Make sure the oven is properly plugged in and that the circuit breaker has not tripped.
- Check the relay board for any visible damage, such as burnt or melted components. If you find any damage, the board may need to be replaced.
- Check the oven's thermostat. It is possible that the thermostat may be faulty and not allowing the oven to heat up.
- Check the heating element. If the element is not heating up, it may need to be replaced.
If these steps do not help resolve the issue, you may need to call a repair technician to diagnose and fix the problem. It is generally not recommended to try to repair an oven yourself, as it can be dangerous and may void the manufacturer's warranty.
1/6/2023 8:10:17 PM •
Dacor Ovens
•
Answered
on Jan 06, 2023
•
94 views
Dacor ecs230sch top oven not working
old post, but this video should help find the reset able thermal fuse
http://blog.applianceboards.com/installs/resettable-thermal-fuse-on-dacor-ovens/
10/28/2021 6:22:27 AM •
Dacor Ovens
•
Answered
on Oct 28, 2021
•
319 views
Not finding what you are looking for?