20 Most Recent
Dacor ECS230 Epicure Electric Double Oven - Page 9 Questions & Answers
On cleaning setting it just
Hello &
Welcome to FixYa
Error code F8
is displayed due to failure of door latch motor and usually ocs when the motor
runs for two minutes without the door locking in the self-clean mode. Replacing
the door latch-lock motor is recommended repair. Please get back to me if you
have any other questions.
Kevin
3/6/2011 7:22:23 PM •
Dacor Ovens
•
Answered
on Mar 06, 2011
We have a dacor double
Hello & Welcome to FixYa
Error code F1 is displayed due to electronic oven control failure and the only way to solve this problem is by replacing the control board which is bad. Please get back to me if you have any other questions.
Kevin
2/3/2011 8:28:49 PM •
Dacor Ovens
•
Answered
on Feb 03, 2011
The oven control lights come
STOP.
I suggest you to check the fuse box and shut off the circuit break that label for the kitchen stove or kitchen.
This will give you some assurance and time to troubleshoot the oven problem.
===
Please reply with MAKE AND MODEL # on reply.
===
I can only give you general fix and check list until you provide the exact model.
Beside the oven light,is there any non-function part in your range?
GAS or ELECTRIC?
=======
For electric stove.
Make sure the electricity supply is off.
Most dial can be pull directly off (outward)
Please give it a gentle tug and see can the oven control dial move outward.
The objective is to clean the dial on the body of the stove.
Please use plastic glove and mild detergent to wipe the post on the dial clean.
Use dry towel to COMPLETELY dry off the post of the oven dial.
Let it dry for 30 minutes or use a fan / oven hood range to speed up the drying process.
Place the dial back on.
Turn the circuit breaker back on and test the oven.
============
Gas oven will need the same cleaning instruction.
The igniter can be worn.
This can be accomplish easily.
I will wait for you reply on the exact model.
1/27/2011 6:09:50 PM •
Dacor Ovens
•
Answered
on Jan 27, 2011
My dacor oven light won't
Sorry to read about your problem, I hope this helps you out.
you have a defective door switch
I tried to help you. Please help me and Rate/Vote on my response. We take the time to answer your question. take the time to rate us.Thanks and good luck
1/12/2011 8:10:50 AM •
Dacor Ovens
•
Answered
on Jan 12, 2011
After oven turn on
F1 means the system watchdog cicuit has detected a fault.
Try pressing CANCEL for 30 seconds if it continues after that you will probably need a replacement control board.
12/13/2010 2:54:21 PM •
Dacor Ovens
•
Answered
on Dec 13, 2010
PCS 127 does not heat up. Fan and preheat start.
We were able to unscrew the plate that sits behind the latch. 6 screws I believe. Look towards the middle back-right side you will see a red switch. Click it twice. Before we put plate back we tested oven and it worked!!! Hope this info will help you. Dacor oven has been a real problem and I'm a kitchen designer. Will never recommend Dacor anything to my clients after many oven issues.
12/12/2010 10:53:03 PM •
Dacor Ovens
•
Answered
on Dec 12, 2010
The oven keeps blinking F2
F2
Heating mode high temperature
This alarm is activated when the ERC senses a runaway heat condition or when the temperature exceeds "runaway limits". The ERC will beep until the cancel or another function is selected. If the alarm repeats the F2 code check the oven sensor and wiring after first checking for a stuck relay. If alarm goes away verify the oven will complete a clean cycle without any type of failure.
11/25/2010 6:21:50 PM •
Dacor Ovens
•
Answered
on Nov 25, 2010
The cooling fan on model
Yes , there is a cooling fan located at the top of the oven
It could be the fan blades catching, or a noisy fan bearing.
You would have to access it by removing the top oven cover to check., and yes it could be as a result of having it cleaned.
Plz rate my solution.
Thanks.
10/25/2010 2:47:53 PM •
Dacor Ovens
•
Answered
on Oct 25, 2010
New MORD227 installed yesterday.
You might have missed some procedures in between. You can use the user manual that came along which describes how to use the model, in the best way possible, including diagrams. Since it's under warranty, don't attempt any of those repairing measures, if suggested by any other expert. If you are not so confident of doing it yourself, you can contact the dealer, who will provide you a company repairman for free. He will teach you everything fine. If you have a habit of forgetting things, try noting it down somewhere.
Cheers. Thank You.
10/16/2010 11:36:44 AM •
Dacor Ovens
•
Answered
on Oct 16, 2010
Clock runs continuously 24 hours
This is definitely just a setting on the unit but I need to know the make and model of the unit to get it fixed for you. What is the make / model?
Thanks
Tim
10/5/2010 3:40:25 PM •
Dacor Ovens
•
Answered
on Oct 05, 2010
When I cleaned the Convection
Hi,
F2 message shows appears because the heating sensor as sensed high temperature.When the ERC senses high temperature then You will get F2 error.Some times alarm beeb will go on.The ERC will alarm and show F2 until the cancel or another function is selected.This is to intimate the oven temperature is beyond level so please let it cool down.
Don't worry this is like error code and for your information it showed up.
post a comment for further assistance.
Thank you for using fixya have a nice day:-)
9/8/2010 5:01:36 PM •
Dacor Ovens
•
Answered
on Sep 08, 2010
Not finding what you are looking for?