Dacor MCS130 Millennia Electric Single Oven - Answered Questions & Fixed issues

FixYourBoard.com will test and remanufacture the relay oven control board in this model. Each rebuild comes with a two year warranty. Reach out to us at 512-355-1108 or [email protected]

this could be the control pwb or touch pad is bad

i just had a similar problem .the door would fall and i had to lift the top of my door hinge to close it .I found that the pin on the door hinge spring had fall.en out . I installed it back and now it works the way it should.the spring should feel tight with no movement.

Are you buying hi quality oven grade lamps for this purpose that'll take the intense heat inside an oven? I wonder if they're halogen or tungsten filament lamps. Defective solder, frosty joints and/or ring fractures on lamp driving areas of a circuit board ARE indeed capable of causing problems with lamps.

sorry this is a common fault with them you cant fix it i have tryed in the passed

That is exactly what the problem is with your oven. Is this the gas model or the electric model?Regards,Richard

Hi This is the Alarm system watchdog circuit : The system has detected a failure in the internal watchdog element , relay circuits and will atcivate a cancel feature. F1 will be displayed in the time digets and will beep until the cancel button or another funtion is selected. An F1 failure could be detected in cook or time of day mode. With an F1 failure the ERC is picking up a comand to supply heat without receiving an input from the membrain. The watchdog circuit is designed to prevent this.If the beep continues after pressing cancel check the main control ERC board.

Typically the self clean cycle is set for 3hours...180 minutes

Open the oven door and unscrew the vented panel at the top. Make sure the oven is off. Atop the electronics in there you'll see a little red button. Push it. Voila.

Open the over door. Remove the four screws holding in the digital display. Pull it off (have something to stand it up on). Look for the small ribbon going between the printed circuit board (PCB) and the digital display you just removed. Pull the ribbon out from the connector on the PCB. On my model, ECS127SBK, push the three right pins down, and re-connect with just the two left pins. Other models, may be different, so you may have to test it out. Be sure to turn off the power at your breaker box while working on it. You won't have the use of the lightbulbs anymore, but you won't have the damn ticking either! (And you'll save yourself getting ripped off from a technician.) I'm not very skilled when it comes to this stuff, so if I can do it, you can too!

Failed control board(micro-processor) replace board.
Known Dacor oven problem-

This is probably caused by a stuck touch pad.

phone 131350

Verify 220 volts of power to the oven. If 220 volts is present and all wires are in good shape, replace the electronic control.

The touch membrane is gone. You can replace it (like i did) and wait for the next thing to go wrong. Took me 3 months for the next problem, and the membrane was $300.

Same problem how do I fix it?

The manual does not say how to change. I would call Decor at (800) 793-0093 to ask them.

This is from manufacture service manual:

-F2- Alarm Heating Mode High Temperature
Is activated when the ERC senses a runaway heat condition or when the temperature exceeds
“runaway limits”. The ERC will beep until the cancel or another function is selected. If the alarm
repeats the F2 alarm check the oven sensor and wiring after fi rst checking for a stuck relay. If alarm
goes away verify the oven will complete a clean cycle without any type of failure.
Another words the problem with oven sensor or relay board. I’m happy to help further over the phone at https://www.6ya.com/expert/vitaliy_f406165329c75ede

Seems to me you having problem with touch panel. It needs to be replace. I’m happy to help further over the phone at https://www.6ya.com/expert/vitaliy_f406165329c75ede

This model actually made this way. Sometime you can not see the thermostat because of the bracket in front of the door latch. When you remove grill panel under control panel you gonna see this bracket. It pulls out very easy. Behind the door latch you will see thermostat with red button on the middle. Before resetting this button make sure you disconnect electricity. I’m happy to help further over the phone at https://www.6ya.com/expert/vitaliy_f406165329c75ede