Frigidaire FAH085N1T Air Conditioner - Answered Questions & Fixed issues

Bad switch or not wired correctly.

If compressor starts, check the running current of the compressor. If amperage is too high together with the discharge pressure, try cleaning the condenser fins and then after cleaning test the amperage and pressure again. If the pressure is still above the normal operating of 300psi, release some freon. If the discharge is too low below 200psi and running ampere of compressor is below the rated ampere of the unit add some freon from the suction line until it reaches 60-65psi. If still suspicious with the unit, try removing all freon charge and evacuate the system to 30 in. Hg to remove any moisture from the system and hold the vacuum for 30 minutes. If no increase in system pressure, recharge and check pressures and amperage.

Check for fan blade defect or possibly loose from its shaft.Check for any obstruction in the cooling fins and use a clamp meter to detect the problem.

Hi,

Here is a tip about troubleshooting your air conditioner...
There are many things that can cause your air conditioner not to cool...

AirConditioner Trouble - Review the Possibilities

heatman101

Did you just buy the unit?

your compressor motor is no good Time to replace unit

replace the rtc overload

Check the filters if clean try cleaning the coils front and back. A hose should do the trick. Just blow through both side try not to bent the fins.

Get a bubble level and make sure the housing is sloped away from the house and yes remove at least one of the drain hole plugs.

No you do not. Not a bad option, but if wall sleeve nstalled properly this unit will not need brackets.

Hi!!

I am assuming that nothing comes on in the display.

Check:
power cord for continuity,
power to board, if OK, replace board.

These are the only two things I can think of that can stop compressor and fan from working.

Don't forget to rate this answer, Good Luck!1

A replace ment cord can be bought at any hardware store , just make sure it is sizes correctly for amperage and voltage.

that is the internal packaging they refer to, it should be a block of foam that is to be removed. You may have to take off the front cover to get to it.

Just adjust the thermostat lower or colder!

if unit is more than 5 yrs old dump it!!! most frigidaire models just dont last...that is why they are so cheap...get it???

Check power at outlet.

A humming sound coming from your Frigidaire AC wall unit after it has been powered off could be due to a few different reasons. I can provide some potential explanations and troubleshooting steps to consider:

• FAN MOTOR
• THERMOSTATE DELAY
• ELECTRICAL ISSUE
• REFRIGERANT FLOW
• OTHER MECHANICAL ISSUES

EPTWFU01 is the water filter part number. It isn't the model number of the refrigerator. Please check the model number. Often the model number is on the back of the refrigerator. Not all models support changing the temperature units. If your refrigerator has a button labeled C/F. Try pressing that to toggle back to Fahrenheit. On another model, FG4H2272UF, press and hold the + and - keypads on the refrigerator side of the control panel for 5+ seconds. One Frigidaire Gallery refrigerator is the GLHS36EJSB. The support page is https://support.frigidaire.com/Owner-Center/Product-Support/GLHS36EJSB . The current link to the manual for this model is https://na2.electroluxmedia.com/Original/Electrolux/Electrolux%20Assets/Document/Complete%20Owners%20Guide/English/241856000en.pdf . This model doesn't allow the units to be changed. The documentation for FG4H2272UF is available here: https://support.frigidaire.com/Owner-Center/Product-Support/FG4H2272UF . See the page 15 of the manual, https://na2.electroluxmedia.com/Original/Electrolux/Electrolux%20Assets/Document/Complete%20Owners%20Guide/English/A10883135en.pdf , for the information above. I hope this helps. Please add a comment with your refrigerator's actual model number for specific directions for toggling between degrees C and degrees F. Cindy Wells

This is likely due to a lack of airflow. Make sure that the air filter is clean and that there are no obstructions blocking the air intake or exhaust vents. If this does not resolve the issue, you may need to have a technician come out and inspect the unit for any other potential issues.