20 Most Recent Xerox Phaser 8860MFP Printer - Page 2 Questions & Answers

This would normally suggest a corrupted file. Try printing from different software. It is also possible that the job is stuck in your print queue so even after rebooting, it is still trying to print the same corrupted file. You would need to delete the file from your print queue or from the printers front panel.
Hope this helps.

Hi,
Here are links where you can download the User manual
Quick user manual
User Guide
Hope this helps.

Unfortunately, Xerox solid ink printers don't print full bleed. It is a shame because in theory, the machine is capable of it but it would require a firmware/driver programming/design update which Xerox are unlikely to do.

The machine will try to keep its temperature at a constant level so this is normal. Also, if you have intelligent ready enabled, the machine will wake up at certain times when it thinks you are going to print. i.e. If you always use the printer at say 3pm to print out the days post, the machine remembers this and will wake at about 2.55pm and warm itself to a ready to print state.
Hope this helps.

Hello,

1st - power down the printer.
2nd - hold the back button and the info button (?) at the same time, without letting go, power up the printer.
3rd - keep holding down the buttons until the XEROX logo comes fully to the center of the screen, keep holding for 2 more seconds, then let go.
I'll take about a minute or two for the Diagnostic screen to come up, the display will turn blank and black but not to worry.
4th - when the Diagnostic screen comes up go to down to the Function or Exercise option, (haven't done it in a while) there will be an option that says
"clear ISC faults" it'll ask you to press OK to confirm, after you do then you will exit Diagnostics and the printer will reboot. You should be fine

Take care.

are you have the installation cd

12 codes on that machine mean a software error.
You can try removing and reseating the RAM chips , most likely its corrupted and will require a software install. The software ( Firmware) would be found at xeox.com, Click on drivers and downloads, then type in 8860 in the search box then click to drivers and downloads again and scroll down to firmware.

Hi guitargurl:
Your printhead is stuck in the tiltposition,or is not able to tilt forward to the print position, due to another problem with a motor
7,010.43: The printhead is stuck in the tilted position, or is not able to tilt forward to
the print position, due to problems.
7,011.44: This is a soft fault, and will not halt the printer.
7,012.45: The drum transfix home sensor is still in a not homed position, after the
return home motion has been completed.
7,014.47: The printhead is not locked in the head tilt restraint spring.
7,015.43: The head tilt restraint spring is out of place.
Troubleshooting Procedure
Step Questions and Actions Yes No
1 1. Reboot the printer.
2. Did this correct the problem?
Complete. Go to Step 2.
2 1. Do the printhead lock arms rotate correctly? Go to Step 3. Repair/replace
the lock arms.
3 1. Has ink spilled ink around the printhead that
prevents the printhead from moving to its
center position? You should be able to
manually push the printhead right to left.
Clean the
printhead area.
Go to Step 4.
4 1. Does the X-axis motor drive the printhead to
it’s center position (so it can tilt forward)?
Go to step 5. Troubleshoot
the X-axis
drive.
5 1. Check the process gearbox for obstructions
or damaged.
2. Ensure the gears are correctly aligned and
homed.
3. Verify the process shaft and drive module
shaft are at their home positions.
4. Did this correct the problem?
Complete. Go to Step 6.
6 1. Has ink spilled on the head tilt gear on its
drive train (near left side of the printhead).
Clean the
gears.
Go to Step 7.
7 1. Use service diagnostics to run the Head
Maintenance Wiper Clutch test.
2. Did the test fail?
Replace the
wiper drive
clutch.
Go to Step 8.
8 1. Ensure the wiper is properly aligned.
2. Use service diagnostics to run the Wiper
Drive Test.
3. Did the test fail?
Replace the exit
module
assembly.
Go to Step 9.
9 1. Use service diagnostics to run the Load
Maintenance Clutch test.
2. Did the test fail?
Inspect the
maintenance
drive system,
replace any
defective parts.

Order an extended maintenance kit. It is very easy to change, just slides in out and into the right side maintenance drawer.
Takes about 2 minutes.

Replace your toner cartridge with a known good one even if it's empty. If the lines are not present you know you need to install a new one.

JM Liabo English only on Fixya please. We are a North American website and only converse in English. hello, I have a phaser 7800? the ignition it puts this code, I switched off and on again? the first switch after 5 seconds as indicated. Same thing, nothing, so I wiped the color sensors. The problem persists. What to do? Call for Xerox Service https://translate.google.ca/?sl=auto&tl=en&op=translate Fixes

Xerox Phaser 7800 - Error Code - PrintCopy .info

https://printcopy.info > model=Phaser+7800 Code: 389.601 · Description: RC Sample Block Fail-A1-In. During the A1 (fine adjustment pattern) and C patch detection, the patch at the MOB Sensor In side did . and more here https://www.google.com/search?q=Xerox+Phaser+Error+389.601.00 ..

Question edited for clarity, full 'make model (what it is)'. check out the videos, however, it is a Xerox and they like to keep track of page counts because it is often part of the contract for lease or toner supplies on their machines. https://www.google.com/search?q=phaser+3260+printer+reset+counter ..

Here is your Service Manual. There are 147 mentions of transfer roller. Press CTRL+F and type 'transfer roller' and press enter. https://www.printerparts-exchange.com/media/custom/upload/Xerox_Phaser_6250_Parts_Service.pdf ..

simple solution call the company's tech support