20 Most Recent HP Laserjet M2727nf Multifunction Printer - Page 3 Questions & Answers

Pickup roller is likely worn out. If you look right where the paper would feed into it, there'll be a cylindrical shapped roller with maybe a flat side on it. If its glazed and shiny, it needs to be replaced. You can kind of scuff it up with something like a scotch or Brillo pad that you would scrub a kitchen pot with and it might work a little longer. Otherwise, you can just buy a new roller, they're not too expensive

You have to be a little bit more specific next time, we have 2 possible scenarios:
A) The printer freezes at the HP LOGO with some arrows
B) Blank display / No display
Both are usualy caused by a problem in the formatter (Mainboard) . There is nothing you can do to recover it. If the printer is still under warranty you will need to call HP (1 800 334 51 44) or take the printer to an athorized warranty depot in your area. This link will help.
http://h20465.www2.hp.com/GPL/search.aspx?language_code=en&country_code=us&SearchType=SSP
I can tell for sure that the warranty for this specific model M2727 will be extended 1 extra year (means you have 2 years coverage) if the printer has one of the issues listed above I Hope this can help You can contact me directly on : [email protected]

Disable sleep mode or update firmware. Cause this is a firmware bug.

http://www.amazon.com/HP-P2015-2015-Roller-Maintenance/dp/B00965WQYI/ref=sr_1_1?s=electronics&ie=UTF8&qid=1377471140&sr=1-1&keywords=rk-p2015Hello,It sounds like the pickup roller is not getting a good grab on the paper. When this happens the roller can not push the paper up into the printer where the next rollers can grab it. this is a very common issue after a year or two of use. The pickup rollers and separation pads come in a kit that is available on Amazon here: http://www.amazon.com/HP-P2015-2015-Roller-Maintenance/dp/B00965WQYI/ref=sr_1_1?s=electronics&ie=UTF8&qid=1377471140&sr=1-1&keywords=rk-p2015

The product has experienced an error in the scanner sub-assembly area.

Turn off the power by using the power switch, wait at least 30 seconds, and then turn on the power and wait for the product to initialize.
If a surge protector is being used, remove it.
Plug the product directly into the wall socket.
Use the power switch to turn the product on.

You need to install the HP Scan software on each and every PC the MFP should scan to. In this software, you can create targets for the "Scan To" button. But: This is only useful when scanning with the ADF, because when scanning from the flatbed, you'd need for every page to hit the "Scan To"-button, press "Scan", wait for about a minute or two until the MFP has found the appropriate PC, and wait for the scan. So network scanning is unfortunately very limited with this machine.

Error 79

• Software/drivers, Memory PCA's, Font-Macro-Personality Cartridges, option I/O Cards. Defective toner cartridge in the Laserjet 4 Plus only. Remove any accessories (font cartridges, memory PCA's, SIMMs, etc.) plugged into the formatter card and try again. If the problem persists and is application specific, verify proper setup with application vendor.

• Defective Formatter PCA - Replace with known operational board and try again. Firmware Update - The configuration page lists the firmware version of the product. Depending on the model, a firmware DIMM may need replacing or a flash update. On flash-memory-based products, you can update the firmware code by downloading the latest flash executable file for the product and running the program according to the readme instructions posted with the update file. If the firmware should become corrupted or fail (usually because of an interruption when attempting to update the firmware), the product will no longer function. In this case, a firmware recovery DIMM is available. Reseat DIMM, then Formatter - Replace or flash DIMM then formatterCan this also be?