RCA 25425RE1 Phone - Answered Questions & Fixed issues
New message light and headset light are flashing
You have unheard messages on the voicemail system provided by your telephone company. This system records messages when someone calls while you're already on the phone. Please contact your telephone company for instructions on accessing their voicemail system.
1/14/2014 12:07:06 AM •
RCA 25425RE1...
•
Answered
on Jan 14, 2014
•
166 views
Un forward line
Normally it's *72 to forward calls and *73 to cancel. If that doesn't work, contact your telephone company for their instructions regarding call forwarding.
1/14/2014 12:06:45 AM •
RCA 25425RE1...
•
Answered
on Jan 14, 2014
•
339 views
I have poor speaker phone qualtity. Do I have to
The speaker phone quality has been one of the sore points of these phones, it has nothing to do with your DSL.
As long as you have a working filter in the line you should have no problem with DSL regardless of the line it's attached to. However, you will have to make sure the wiring is done correctly for the intercom to work.
7/21/2010 1:14:21 PM •
RCA 25425RE1...
•
Answered
on Jul 21, 2010
•
164 views
4 line phone intercom
Since this is more of a Peer to Peer system, the distance might be the problem. There is no control unit to push the signal.
6/2/2010 12:01:26 AM •
RCA 25425RE1...
•
Answered
on Jun 02, 2010
•
376 views
Speaker phone problem
It is possible. I have ATT 945(?) 4 line phones that communicate via a DSL-like signal between units to do special things like intercom, etc.
What I have in my setup is that I have a seperate line from the point of entry of my phone line to my DSL modem.
I then have TWO stacked DSL filters PER LINE that feed the main phone line running to all the phones.
Be AWARE that when using the speaker phone there is a modulation of the gains both directions. When you talk OR have a noisy background noise, the gain of the speaker is cut down to prevent feedback. And when you go silent, the speaker gain is increased for you to hear the other side of the call. Essentially it takes as much discipline as the old two-way radios... one talker at a time with these speaker phones AND very little background noise.
1/9/2010 5:16:59 AM •
RCA 25425RE1...
•
Answered
on Jan 09, 2010
•
726 views
How to configure call forwarding on RCA RCA Phone model 25425RE1-
CALL FORWARDING HAS TO BE DONE THRU THE PHONE COMPANY IF YOU HAVE CALL FORWARDING - AND I DO THIS IS WHAT I DO - I HAVE AT&T IN MEMPHIS TN PICK UP HAND SET AND HIT *72- YOU WILL GET A BEEP- DIAL THE PHONE # YOU WANT TO FORWARD THE PHONE TO - SOMEONE MUST BE AT THAT PHONE NUMBER TO ANSWER IT! ONCE THE LINE IS ANSWERED- THEY HANG UP AND THEN YOU HANG UP AND PHONE SHOULD BE TRANSFERED- I ALWAYS TEST IT TO UN- TRANSFER IT PICK UP PHONE AND HIT 73# AND IT WILL BEEP 2 TIMES- NOW PHONE IS NOT TRANSFERED ANY MORE
1/25/2009 11:20:20 PM •
RCA 25425RE1...
•
Answered
on Jan 25, 2009
•
9,876 views
My speakerphone doesnt work on my 25423re1-a ,but my handset does work ? how can i fit it , thanks Ben Brazzell
Ensure that the speakerphone feature is not disabled. Some phones have a dedicated button or an option in the phone menu to enable or disable the speakerphone. Look for this option and make sure it is turned on.
Or Reset the phone to factory settings. Refer to the user manual of your 25423RE1-A phone for instructions on how to perform a factory reset. Keep in mind that this will reset all settings and may delete any personalized configurations.
How do I turn off a second alarm on the RCA Digital PLL radio model RP3711A?
To turn off the second alarm on the RCA Digital PLL radio model RP3711A, follow these steps:
1. Press and hold the "Alarm 2" button on the top of the radio until the display shows "OFF."
2. Release the button.
3. Press the "Alarm Set" button to confirm that Alarm 2 has been turned off. The display should no longer show the time and alarm settings for Alarm 2.
If turning off Alarm 2 using the above steps doesn't work, you can try resetting the radio to its factory settings. To do this, follow these steps:
1. Unplug the radio from the power source.
2. Remove the backup battery from the radio.
3. Wait at least 30 minutes.
4. Reinsert the backup battery and plug the radio back in.
5. Set the time and alarm settings again.
Regarding the manual, the model RP3710 and RP3712 may have similar features and operation, but it's best to refer to the manual specifically designed for your radio model RP3711A to ensure that you are following the correct instructions. You can usually find the manual online by searching for the model number on the RCA website or on other electronic manual databases.
Not finding what you are looking for?