Top 20 NComputing L230 Network Terminal Questions & Answers

For security purposes, this process cannot be disclosed in an online guide. For assistance resetting an L-series firmware password, please contact NComputing technical support directly at http://www.ncomputing.com/techsupport

All of them.

SARATH BABU Simple press ctrl + shift + end key if its ask password

a problem with your network cable.try to climb again

Here's a video Nitin Sharma suggested as a solution to your problem from YouTube:


NComputing L300 Ethernet Virtual Desktop

check the network cable

download from ncomputing website they have it for win 7

change your keyboad

Please reimage your terminal to factory settings. Necessary software is available from ncomputing at http://www.ncomputing.com/support/software-downloads

you will need to open up your network connections click start control panel network connections this may vary depending on your operating system look for local area connection if you see a red X or a yellow exclamation or question mark ! ? you will need to update or install the driver or it could be firewalled click start control panel administration tools computer management device manager scroll to network adapters should see a yellow question mark? right click install drivers the driver might be on the disc supplied by your ISP internet service provider or the motherboard disc or you might download one if you dont have on a disk

Make sure you Ethernet is enabled in bios restart your computer during the boot up process you will see on your screen a certain key to

press to enter set up (BIOS) press and hold that key to enter bios using arrow keys scroll to intergrated peripherals

look for SiS On Chip Pci Device press enter scroll to SiS 10/100m press enter make sure its enabled hope this helps

if you dont have a motherboard disk or a disk with the drivers you will need to download them http://download.cnet.com/2000-20_4.html on the home page you should see a search tab just type in what you are looking for

IE: motherboard name ethernet driver you might have to try a few times to get it right

hope this helps

It's very simple, register your vSpace software and enable the background hardware activation. I would recommend the online registration as it's the simplest and fastest. The registration can be found in the Programs fly out menu under the NComputing Group.

There is NO reset button. Call their Tech Support at 888-365-1210, they can tell you the key combination to reset the password if their is one.

a fixed ip address while password protected the gadget

Not sure what you mean by LAN workgroup. If you're referring to traditional Local Area Networked PCs and sharing files on a server, the NComputing solution is very different. Imagine taking a standard LAN with 20 PCs, each costing at least $500 (usually much more), and having them access a network. That cost would run you $500 * 20 or $10,000. That's just for the hardware, not any of the soft dollar costs. Additionally each PC uses a minimum of 100 Watts of Power, more common these days is 250 Watts.
Now take the NComputing solution. Start by replacing ALL 20 PCs with a $150 L230 or a $200 L300 device, which only consumes 5 Watts of power. Purchase one server, say $2,000. Load up NComputing's vSpace on the server and connect all of the L devices through the network. Every user still gets their own desktop, access to the network and other peripherals. And the I.T. department now has ONE Desktop OS touch points, not 20 as they did before. Thus the NComputing solution can reduce support costs, consume less CapEx and OpEx budget while delivering desktop sessions to each user. In this example the cost would be $2,000 + (20 * $150) = $5,000.

The L230 does not have a factory reset. If you need to clear a forgotten password, simply call NComputing's Tech Support at 888365-1210.

It should work fine. As long as the SAP client is 'multi-user' aware then you're good to go. One 'acid test' is to see if the SAP client will work on a Terminal Server or a Citrix Presentation server and in this case it does. The NComputing solution, conceptually at the application layer, behaves much like TS or Citrix, thus looking for those solutions is what you'll need to know for NComputing. Here is the website I found about how to setup specific INI files for Citrix to get the SAP client working. My recommendation would be to test as is out of the box with two NComputing seats, simultaneously. If that fails, then try the suggestions on this website: http://community.citrix.com/display/adi/SAP+GUI+7.10+on+Citrix+Presentation+Server.

Hi!

Please download and install the latest software for your operating system from here:

http://www.ncomputing.com/softwaredownload

Hope it helped.

Hi

Not clear whether you installed SP1 on the client or the server.

Try resetting or powering off and on the L230 and let it reintroduce itself to the network.

Also restart the computer that had the SP1 installed on it.

If none of the above resolves the problem, enter Network settings on the client and ensure that Neywork Discovery and File Sharing are not turned off. If they are off, enter Network and Sharing Center and use the Drop Down arrows on the right to turn them and any other desired options on.

Hope this helps.

My recommendation is to uninstall the vSpace software, reboot, run their cleanup utility, and reinstall the latest version. Before reinstalling, make SURE that you have applied any Service Packs and ALL of the current MS updates. Additionally, browse Device Manager and make sure there are NO missing or conflicting drivers. Do NOT, I repeat, do NOT install from the provided CD. As of this posting date, the cleanup utility is available here: nc-eng.com/tools/ncuninstall. The most up to date vSapce for L230 is on the NComputing download site. If you hit this post later and the supplied URLs are not valid call NComputing TS at 888-365-1210. Lastly do NOT forget to register the vSpace software.