Top 20
3Com Baseline Switch 2924-SFP Plus Questions & Answers
I forgot ip address and password and want to factory reset
Connect the console cable, open a connection to the serial port via a utility such as PuTTY, and do the following:1) Enter the user name "recover" and password "recover" to place your unit in password recovery mode. The unit will remain in password recovery mode for 30 seconds max.2) Perform a hard reset by removing power, waiting 10 seconds, and then re-applying power.3) Once the switch has rebooted, enter a new password for the "admin" user account.4) Enter enable to leave password recovery enabled, or enter disable to turn it off. You are now logged in as the default "admin" user.Note: If password recovery has been disabled, the only way to recover access is to return the switch to 3com.
Forgot ip address and password
To re-enable the Console access requires the SW2900 series to be reset to its default settings via the WEB INTERFACE
- Web Interface
- Device >Configuration >Initialize To
change the Default User "ADMIN" password it is necessary to use the
Console connection
-Console Interface
-Once the unit has successfully booted and the prompt presented
-Enter "password" (without "")
-Enter "admin" when the system prompts for User
-Press the "Enter" key when the system prompts for "Old Password" (the ADMIN password was reset by the Web Interface commands)
-Enter "" when the system prompts for the New Password (where "" is the new product ADMIN password)
-Enter "" when the system
prompts to confirm the New Password In order to complete the
configuration it is necessary to save the configuration via the WEB
INTERFACE
-Web Interface
-Device > Configuration > Save
Symptom:
SW2900 Baseline Switch - Default console access disabled following password change
From the web interface, the default user "admin" password is changed and console access is disabled
Cause:
When applying the new password, by default
the service-type is set to "telnet". When applied, the default
"terminal" setting is removed thus disabling console access.
I have 3Com Baseline Switch
First,"There is usually a small button on routers that can be accessed with the tip of a pen or a paperclip. When you find that tiny button, hold your pen or paperclip down on it for approximately 10 seconds until the router resets itself to factory defaults."After that, you can contact the manufacturer to get some helps if you still have problem.BTW,I work for Ingellen Communication Equipment and we are a large fiber optic equipments manufacturer in Shenzhen.Kindly let me know your specific requirements so that i can help
I have AVI Video and it only plays sound
Ok it is may be do you to system is old needs up to date , so that the video may not have downloaded completely from the source web portal. The media player present in your handset is outdated.
HI,
I have two 3com
I don't know anything about these units, nor do I have time to source any docs for you, but maybe you can try connecting a PC directly to the port your patch panel is connecting the the switch from, you can at least see if that port is working.
My next and only other suggestion is to invest in a "LAN cable tester". In my area, you can find cheap ones for U$20.
The tester will allow you to check connectivity between any two ports, and allows you to test both patch links and individual CAT5/6 cables.
Good luck!
Facebook recovery
notify the police dept / person handling the case and let them know about the face book information
I want to know how I can re-set my 3Com 3crwe955275 wireless access point to its default factory settings. Can anyone help?
1 Remove power from the Gateway.
2 Disconnect all your computers and the cable/DSL modem from the Gateway router.
3 Using a straight through Ethernet cable, connect the Ethernet Cable/DSL port on the rear of the Gateway to any one of the LAN ports.
4 Re-apply power to the Gateway. The Alert LED will flash as the Gateway starts up, and after approximately 30 seconds will start to flash more slowly (typically 2 seconds on, 2 seconds off). Once the Alert LED has started to flash slowly, remove power from the Gateway.
5 Remove the cable connecting the Cable/DSL port to the LAN port, and reconnect one of your computers to one of the Gateway LAN ports.
6 Re-apply power to the Gateway, and when the start-up sequence has completed, browse to:
http://192.168.1.1
and run the configuration wizard. You may need to restart your computer before you attempt this.
7 When the configuration wizard has completed, you may reconnect your network as it was before
Here on page 85 of the manual
3Com 3CRWE53172 User Manual Forgotten Password And Reset To Factory...
How reset 3com 4228g switch
If I remember correctly, there is a tiny hole at the back or on the side. Press a paper clip into it. The switch should do a full reset and then reboot. If its just locked up, I would switch off at the power for 15 mins and try let it do an auto restart itself. Do this before you go doing a full button press reset as you may lose any or all updates the switch has had loaded into it.
Www google omegle
There could be a lot of reasons, one is port blocking, the other is firewall, there caould also be NAT port issues, what modem and internet provider do you have could be the problem.
3COM 3100 entry phone, how to configure SIP
From Digium Mailing List:
3Com 3100 series phones do not support SIP with non-3Com systems. They have a basic boot loader which must download code from a 3Com NBX or a 3Com VCX system. If you don't have either of these, then you won't get runtime code on the phone, thereby making it impossible to use the thing with Asterisk.
Asterisk Users 3Com Phones
What is 3x phone
For 3Com that would mean a 3100 series or 3500 series phones. The 3100 series phones are for NBX and VCX phone systems and the 3500 series phones are for VCX only. Both are also SIP compliant.
Db9 rj45 pinout
Here is the standard pinout for a console port on a router to seriel port for computers
Network card driver
Are you able to remove the card from your PC?
and read the model on it?
Are you able to find your motherboard/computer model?
use the motherboard/computer model to find what model of card is on it.
Once you have the nic model search for a driver.
Not finding what you are looking for?