20 Most Recent Frigidaire 24 in. PLD2850 Built-in Dishwasher - Page 4 Questions & Answers

Hi,

Here is a tips that I wrote that will help to explain why you get the PF Error Code

PF Error Code for Appliances

heatman101

==-]=-

You could have a problem, maybe something has plugged and is causing stress on a pump motor (wash cyc) or drain pump... something stuck in discharge baffle unit must be removed for easy axcess to said assembly.

Hi,

That is not that hard to fix and you can easily buy the parts yourself online...

Here is a tip that will help you with the online buying...

How to Buy Appliance Parts Online

heatman101

then if it is leaking from the front. you need a new seal around the door and it is not that hard to change but remember to always work safe,

First of all how do you know the thermostat and the heater were bad?
Did you check both parts with a volt meter by checking continuity/resistance?

First thing we need to do is if you dont already know, learn how to use a volt meter. It takes all the guessing out of the troubleshooting.

Watch the movie click the link http://www.youtube.com/watch?v=nddAA5IAUik

You will need to check for power at the heating element when in the dry cycle 110vac
let me know about the voltage reading email me [email protected]

Sounds like it's not being told to turn on.

if no voltage at the heater,you will need to trace the power source back to the control. Which is located behind the control panel where your touch panel is in the front top of the unit.

Hi,

Here is a tip that I wrote that will help you with your dishwasher not draining problem...Dishwasher Problems - Water will not drain outheatman101

the pump is being blocked by something it needs to be cleared.

Hi

To reset the control press and hold the AIR DRY/RINSE ONLY/HEATED DRY button for 15 seconds, if it wont work then the control board should be replaced. Hope this helps...please post back for further assistance.

Daniel

Hi

It seems that the unit is not draining completely and dishwasher not draining issue usually occurs due to kinked drain pipe, clogged drain filter or drain pump. Please check that the drain pipe, pump or filter is not kinked, clogged or any foreign object is stuck there. Check the drain hose for any visible clogging, remove if present. If no visible clogging or lint is present then you'll have to remove the drain hose. If still not visible then the drain filters or drain pump is clogged and you'll need to clean the drain filter and drain pump. Please also note that dishwashers don't drain out the complete water such that heating element doesn't overheat. Hope this helps... Please post back for further assistance.

Daniel

Hi

Error CL appears when the dishwasher control detects door switch is open or door is open. You'll have to open the door and check the continuity of the door switch. If the door seems to be closed then it is the control has detected an issue with the door latch. Check the door latch & seals to make sure door is closing fine. Unplug the dishwasher from power outlet and wait for 10-15 minutes. Restart the dishwasher and check if the error is still there. If error still appears then you'll need to repalce the door switch/door latch. Hope this helps... Please post back for further assistance.

Daniel

Hi,

Here is a tip that I wrote that will help you with your dishwasher not draining problem...

Dishwasher Problems - Water will not drain out

heatman101

Sorry to read about your problem, I hope this helps you out.

you have a clogged pump,hose or sump area

I tried to help you. Please help me and Rate/Vote on my response, thanks and good luck

You can replace the nuts. I went to fridgidaire.com and found the part number, then called around to a few appliance parts stores. Peice of cake, and only cost a few bucks. I don't trust those nuts because they crack, apparently, but the threading is super wierd so I don't see an alternative but to replace it with the same nut.

I was having the same problem with water sitting at the bottom of my dish washer. I had recently installed a new garbage disposal when the problem started. You need to make sure that you knock out the inlet valve where the disposal drain line hooks up. If you have never hooked up a washer to your disposal, this piece will be in place. Stick a flat head screwdriver in where the drain hooks up and hit it with a hammer and the small plastic circle will pop out. The washer does not use any water when that is blocked and therefore will leave the old water to turn rancid...I hope this helps!

Hello & Welcome to FixYa

Flashing green light is reset by pressing two buttons in sequence 3-4 times, to reset your kenmore press these buttons in sequence:

High temp wash-heated dry-high temp wash-heated dry

Please get back to me if you have any other questions.

Kevin

Check around the bottom of the dishwasher checking to see if pump filter screen is blocked. if clear check the hose connection at the sink to be sure it is clear.

Hi
Dishwasher not draining issue usually occurs due to kinked drain pipe, clogged drain filter or drain pump. Check the drain hose for any visible clogging, remove if present. If no visible lint is present then remove then turn off the dishwasher and remove the drain hose and check for any visible clogging. If still not visible then the drain filter or drain pump is clogged and you'll need to clean the drain filter and drain pump.
Please note that dishwashers don't drain out the complete water such that heating element doesn't overheat. Hope this helps... Please post back for any further assistance.
Daniel