20 Most Recent Frigidaire FWS833A Top Load Washer - Page 9 Questions & Answers

Hi Linda,
If the hose is OK, the the pump is either clogged or has gone out. If you the the front panel off, the pump is to the front on the left, you will see 2 hoses on from the tub to the pump and one from the pump and to the back of the washer.

check the motor plug it might not be pluged in all the way or may have a bad connection in the plug

If you are not getting any noise whatsoever, you may have a defective lid switch or timer. If you hear a distinctive hum or buzz followed by a click and then no hum, the unit has a defective motor.

If you can hear the motor during the agitate cycle, the the transmission has stripped gears.

dont think thats the model # cant bring up anything on it sounds like the brakes ... is it when it slows down to stop?

Did you checked the pump ? Does it make any noise ? The washer will not move to the spin stage if water will not pump out from drum.

You probably have bad spin tube bearings. Look above transmission for a water leak or evidence of one.

Check out your outlet filter, probable it is clogged. Clean this out and refit. Most cases when the drain or spin does not work, it is the filter. This is a suggestion.

Eileen, If the screeching is only happening on the fill and not during agitation or spin, I think we are safe to rule out the belt, pulley and bearing. Remove the fill hoses from the back of the washer and check to see if you have sand or gunk caught in the screens of the valve itself. If they are clear sounds like the water passing through the valve is making the noise. Another thing to check is the water pressure in the house. It should be around 55 psi., 75 psi max. I have seen it as high as 120psi with a bad regulator. This will cause noise and all kinds of problems. The part number for the fill valve is 131389300, according to the model posted....Catriver...post back.

Good Morning Anonymous, this is Z. I am happy to assist you! I understand that your door indicates it is open and your dryer will not operate. Let's attempt resetting your dryer by either unplugging it or flipping the household circuit breaker off. It is good to wait approximately ten minutes and turn on your dryer. Select a normal cycle and verify if your dryer will start. If your dryer will not operate then it possibly have a faulty door lock assembly or a communication problem with the control board. At this point, it would be advisable to contact an experienced appliance repair tech to assist further.

Sure sounds like your timer has bit the dust. I'm not sure if the timer is still available. You have a great washer there. Good luck.

The machine does not exist as you have written it. There are two likely reasons The door switch has failed and hasn't passed the self test procedure. or the control board / timer has failed. Try power cycling it. Remove the mains plug for an hour. It is has an On Off button press it for a minute. For a knob, full it and leave two minutes. Plug back in and try again. https://www.google.com/search?q=Frigidaire+FWAC+19B5MSGNW ..

crowbar?

Maybe try this...... https://yellowfevereats.com/frigidaire-affinity-washer-reset/

Hi, Please power cycle your dryer and attempt to run it again. If this fails, please ensure that your clothes are evenly distributed so that they weight of the clothes doesn't cause the dryer to be shutdown. Just to double check, please ensure that you've cleaned the lint track of your dryer. Lastly, you can use an power outlet extender to help switch the power outlet that you're using to run your dryer as there might be something wrong with your current one. Thank you.

There could be several issues that could cause your Frigidaire dryer to stop running after just a few seconds. Here are a few potential problems to consider:

1. Thermal fuse: The thermal fuse is a safety device that shuts off the dryer if it overheats. If the fuse has blown, the dryer will not run.
2. Clogged dryer vent: If the dryer vent is clogged, it can cause the dryer to overheat, which could trip the thermal fuse.
3. Faulty cycling thermostat: The cycling thermostat regulates the dryer's temperature. If it's faulty, the dryer may not run for more than a few seconds.
4. Faulty start switch: If the start switch is faulty, it could prevent the dryer from running.
5. Faulty door switch: The door switch prevents the dryer from running when the door is open. If the switch is faulty, the dryer may not run.

To fix the problem, you'll need to diagnose which of these issues is causing the problem and then replace the faulty part. I recommend having a mechanic diagnose and fix the problem for you.

The E11 error code indicates a problem with the gas sensor DE32-60011A and or the wire harness DE39-40678D. Unfortunately the manufacturer has discontinued the sensor. You may want to try contacting local parts dealers, one of them might still have it in stock. Enter your part number in a search engine, a smaller company might have it or try eBay, Amazon or similar sites . Search by using the manufacturers part number. Try a used appliance store, sometimes they have the same model or a usable part for your machine.

If it is new, didn't it come with an operating manual? Videos here https://www.google.com/search?q=Frigidaire+Gallery+GRFC23534FO+sabbath+mode

How do I set Sabbath mode on my refrigerator? - Frigidaire

https://www.frigidaire.ca > ... > FAQs > Refrigerators Depending on your model, the Sabbath mode is turned ON or OFF by simultaneously pressing and holding for 5 seconds both the:"v" and "+" orThe freezer "-" and ...

Help and videos in the link https://www.google.com/search?q=frigidaire+stackable+washer+not+agitating ..