Top 20 MTX Thunder 3401 Car Audio Amplifier - Page 7 Questions & Answers

In modern cars, the Body Control Module (BCM) runs the radio and communicates on the computer bus network. It gets confused when you put another radio in it. You are not alone! https://www.google.com/search?q=2008+Audi+A3.+I+have+installed+an+aftermarket+radio+but+the+rear+speakers+and+built+subwoofer+won%27t+come+on ..

Here's the manual user for it: Kenwood KDC-128CR, KDC-1028, KDC 128 User Manual (manualmachine.com)

Question edited for clarity, wrong type of 'to', 'two', 'too'. Question moved to Car Amps category. It sounds like is has failed electronically Swap the amps over physically. Take the one for the subs and put it on the other speakers and and put the working amp on the subs. If that makes the subs work, you take the failed amp for repair of buy a new one that will damage your hearing by the time you are 35. I am 70 and have tinnitus from listening to loud music in my 20s!

Look at the wire and look at the contacts where the wires got torn away. Normally there is some type of clue to where they came from. In general terms red or brown is live and black or blue is negative, green is ground. The seller gives Lifetime Tech Support. They can check for you. https://www.onlinecarstereo.com/CarAudio/p_44441_Performance_Teknique_ICBM-BT110X.aspx https://www.google.com/search?q=performance+teknique+icbm+bt110x+wiring+diagram ..

If you mean the FM station for a bluetooth connection, its ususally 88.2 to 95. It will depend on the bluetooth unit you have. Try stations from 88.0 to 95 in increments of one until you get the clearest reception.

Question edited for clarity. This is the Unit? https://www.amazon.com/Life-Gear-LGTF38-Flashlight-Weatherband/dp/B000XOO01S/ref=cm_cr_arp_d_product_top?ie=UTF8 It says it has rechargeable battery and can also be run on the mains and also AA batteries. The rechargeable batteries will be Nickel Metal Hydride and charged up by the crank.. The reviews are very mixed! https://www.amazon.com/Life-Gear-LGTF38-Flashlight-Weatherband/product-reviews/B000XOO01S There are no resources on replacing the battery apart from saying 'Do not try to remove or replace the batteries'! https://www.google.com/search?q=life+gear+LGTF38+battery+replacement The Reviews on Amazon give some clues, but not a lot. My advice is Send it BACK! 5. It includes the rechargeable battery in the package, and it will also run off of regular batteries. The hand crank can be used to charge the rechargeable battery or you can charge from a wall plug, also included. ..

dealer with vin and proof of ownership

If your car audio system requires a code to unlock it, there are a few options you can try: Check the user manual: The user manual for your car audio system may contain information on how to unlock it if a code is required. Look for a section on "security" or "anti-theft" features. Contact the manufacturer: If you don't have the user manual or can't find the information you need, you can try contacting the manufacturer of the car audio system. They may be able to provide you with the code or instructions on how to unlock it. Try common codes: Some car audio systems use a default code, such as 0000 or 1234. Try entering these codes to see if they work. Reset the system: If none of the above options work, you may need to reset the car audio system. This will erase any saved settings and data, including the code. The process for resetting the system will vary depending on the make and model of your car and audio system. Check the user manual or contact the manufacturer for instructions.

Question edited for clarity. Normally you need a harness if it is going in a different vehicle. Crutchfields sell them https://www.google.com/search?q=Toyota+nhdn-w56+wiring+diagram ..

Question edited for a lot more clarity. Here is the manual. This is an aftermarket unit unit so there will be an inline fuse on the power wire This one is a good diagram and shows 10 amp fuse on the yellow wire to the battery. Make sure it is connected there at the battery, but the installer may have just spliced into a live feed up behind it.. https://www.manualslib.com/manual/40984/Dual-Xdvd8181.html?page=5#manual

For Clarion radio codes contact this link with all the serial numbers from the radio and they will generate the code for you quickly and cheaply: https://www.vivastreet.co.uk/car-parts/hayes-ub4/car-audio-security-code/311088168

Remove the flame spreader and put it in a pan of cold water with a teaspoon of washing up liquid. Bring it slowly to a simmer. Be careful because it will want to boil over. Turn off the gas and leave it to cool. Use a plastic pot brush to clean and push the bristles down the holes in the flame spreader. Rinse and put it back, making sure it is seated properly. Most have a notch they must drop into.

Question edited to tidy up the written English. This looks link it might be a winch, but you posted to Car Audio! https://www.google.com/search?q=liebmaya+wireless+winch+remote+wiring+diagram ..

The Proton D940 stereo receiver features both analog and digital inputs, so you have a few options when it comes to connecting a CD player to the receiver. For a digital connection, you will need a CD player with a digital output, such as a coaxial or optical output, and a digital cable to connect the two. Look for a CD player with a digital output labeled "coaxial" or "optical" and purchase a cable that matches the output on the CD player and the input on the receiver. For an analog connection, you will need a CD player with analog outputs, such as RCA outputs, and an RCA cable to connect the two. Look for a CD player with an analog output labeled "RCA" and purchase an RCA cable with the appropriate connectors to match the CD player and the receiver. Once you have the CD player and cables, connect the CD player to the Proton D940 stereo receiver using the appropriate input on the back of the receiver. If you are using a digital connection, select the appropriate digital input on the receiver using the input selector button on the front of the receiver. If you are using an analog connection, select the appropriate analog input using the same input selector button.

This is the 3 ways to get a radio code Jane. We get asked it so often, I wrote a FixYa Tip on it. https://www.fixya.com/support/r29874205-need_vehicle_radio_code ..

If your device is stuck on the CD button and you're unable to change it, try the following steps:

1. Check the device's manual: First, consult the manual for your device to see if there are any specific instructions for changing the input source. Some devices may require a particular button sequence or menu selection to switch inputs.
2. Power cycle the device: Turn off the device and unplug it from the power source for a few minutes. Then, plug it back in and turn it on again. This may help to reset the device and allow you to change the input source.
3. Check the remote control: Ensure that the batteries in the remote control are working properly and that you are using the correct remote control for the device. Some devices may require a specific remote control to change inputs.
4. Try a different input: If you're unable to change the input from the CD button, try selecting a different input button such as the radio or auxiliary input. This may help to reset the device and allow you to change the input source.
5. Contact the manufacturer: If none of the above steps work, contact the manufacturer for assistance. They may be able to provide additional troubleshooting steps or suggest repairs or replacement options.

Hopefully, one of these steps will help you resolve the issue and allow you to change the input source on your device.

there are a few things you can try that may help to resolve the issue: 1. Check the screen for any dirt or dust buildup and clean with a soft cloth and some cleaning solution, if necessary. 2. Make sure you are using the correct touch settings. On the main menu, select "Settings" and then "Touch Settings". From here, make sure the "Touch Function" is set to "on". 3. Try a reboot of your receiver by pressing and holding the "Power" button for 10 seconds. This should reset the system and may be able to fix any underlying connection or hardware issues. If all else fails, then it may be a hardware issue