20 Most Recent
MTX Thunder 1501D Car Audio Amplifier - Page 2 Questions & Answers
Lookin for specs
the 1501d is a one channel amp! But has two terminals for that same channel. that amp is stable to produce say 700 watts into 4ohms but also stable to produce 1500 watts into 2ohms.If you were to have two 4ohm speaks it would be easier to have a terminal for each speaker.good amp btw but be careful with their fragile preamp inputs
1 ohm stable?
YES IT IS i have the same amp and i have it to 1 ohm its powering to kicker l7's which are 2ohm subs down to 1 ohm stability
What is the long volume/bass control"s proper name.
the Control you are talking about is an External Bass Control also known as EBC knob you can probably find one at MTX.com or crutchfield.com or any authorized MTX dealer. Please vote and leave high marks. Thank you
No out put sound
Check all fuses on the amp first. If the fuses are good then make sure the remote wire is hooked up. If you dont wanna run the remote wire from the amp to the stereo then all you need to do is run a wire from the remote on the amp to the power on the amp. if the remote is not hooked up then you will get NO SOUND
I own a mtx 1501d.Also own a 18
THE AMPLIFIER NEEDS A 1 OHM LOAD AND YOU HAVE THE RIGHT SPEAKER TO PROVIDE THIS LOAD. THE AMPLIFIERS TERMINAL STRIP PROVIDES YOU WITH 2 POSITIVES AND 2 NEGATIVES, BUT THEY ARE ONLY FOR CONVENIENCE WHEN WIRING 2 DRIVERS. ACTUALLY THE 2 POSITIVES ARE THE SAME CONNECTION INTERNALLY ON THE BOARD, AS WELL AS THE 2 NEGATIVES. THAT BEING SAID, THE SIMPLEST WAY TO CONNECT YOUR SPEAKER IS TO PARALLEL THE VOICECOILS IN THE BOX BY CONNECTING THE 2 POS. TOGETHER AND THE 2 NEG. TOGETHER THEN RUN THAT POS. AND NEG. OUT OF THE BOX AND SIMPLY CHOOSE EITHER OF THE 2 POS AND NEG. OF YOUR CHOICE AT THE AMP. IF YOU EVER HAVE TO ADD A SUB, THEN YOU WILL HAVE 2 MORE TERMINAL LEFT OVER ON THE AMP. TO CONNECT IT TO AT THAT TIME. BY ALL MEANS, IF YOU WOULD LIKE TO RUN EACH COIL SEPARATELY OUT OF THE BOX AND CONNECT THEM TO ALL 4 TERMINALS, THEN THIS IS FINE TOO, AS EITHER WAY, THERE WILL BE NO DIFFERENCE WHATSOEVER. LET ME KNOW IF I CAN BE OF FURTHER ASSISTANCE....V
1501d,, What subs should i use/
I would stick with Kicker or MTX. The best place in my mind to get them is soncelectronix.com
Just try to mach the specs as close as possible. Make sure to look at the recommendations of the subs for the size of the box and the port volume.
Ran it at 1@ now it has low power
Hello if your amp is the one above in the picture, MTX-1501D then your amp is not 1 ohm stable. Your amp is rated at 500 watts x 1 at 4 ohms and 1000 watts x 1 at 2 ohms. The amp has a safety circuit that if it senses to low of a load, ohms, it will only put out half it's power to protect the amp from shorting out. Read the manual. You can download it at retrevo.com or just google it and a manual download site will be in the search list. Hope this hels, Good luck. Btw, I’m available to help over the phone in case u need at
https://www.6ya.com/expert/mark_b53a7494531bf96d
Mtx thunder 1500 watt amp no sound
Even if there is no visible damage, it could be that one of the transistors is blown, Use a multimeter to check the resistance of the transistors.
I have a mtx thunder 1501d..i have the power cord
Hello tonytone54,
The ground should go directly to the vehicle frame, never through a cap, fuse, or anything else. Also, if you are connecting positive through a cap, make sure that you charge the cap before connecting it.
Hope this helps.
Need help MTX 1501d amp diagram
Remove cover and set in direct sunny window for long time, may be no problem with it, Took a month to dry one of my amps out enough that it decided it would come back to life, cell phone dropped in sink took 2 weeks, If you try power to it too soon --fried--, good luck finding diagram and repairing it sincerely-hope its okay, good amp, bad luck,
Most power out of amp w/out blowing subs
you may only be able to get but so much out of the subs. If you turn the bass down a little so the that you dont drive the subs so hard you may get a little more wattage out of them
I don't know how many watts is this amp
ECLIPSE makes a 32440
If this is the amplifier you are looking for specs on...
4 x 85W @ 4 ohms (13.8V - 0.1% THD)
4 x 120W @ 2 ohms (13.8V - 0.1% THD)
2 x 240W @ 4 ohms bridge (13.8V)
Thanks for using FixYa -a FixYa rating is appreciated for taking the time to answer your Question.
Amp problem
These amps have a problem with broken shield connections on the RCA jacks. If the shield breaks loose from the frame of the RCA jack, you will have this problem. If you disconnect the amp from power and pull the cover, you can check to see if the shield is loose in the frame. if it is, it needs to be soldered.
You can also have this problem if the shield ground opens on the head unit.
No boom in my box
Whats up!!! well check this out. The sub isnt working at all? don't hear anything from it? more then likely it can be one of the following problems.
before you do these steps make sure that the amp levels are all the way low so you dont have a chance in poping the sub for unnecessary jolts of power
you can check to see if the sub itself is good by getting a AA and touching each of the speaker +- on the sub see if you hear anything. More then likely the sub itself is good.
Moving on to the amp. Do you see any lights? red/green? or none
if no lights check the pos/neg terms and make sure there properly installed. have to check underneath the hood for that while your there check the fuse if its a inline one if not then there should be a fuse located on the amp itself.
if you see green then the amp is getting power and the amp is properly grounded
if nothing check the grounding and make sure thats its connected to the frame of the vehicle either by sanding down a small piece of the metal exposing the silver and using a self-tapping screw.
feel free to contact me via yahoo messenger if you have any questions
always forward-jcbproducts
ym-jcbproducts
Not finding what you are looking for?