20 Most Recent
Frigidaire GLTR1670A Front Load Washer - Page 7 Questions & Answers
My washer wont spin out it has a code that is E20
Check your exit hose spigot, it may be clogged. This is if your filter is all clean. There should be air for passage in the standpipe behind. Your hose should not fit airtight into the standpipe and neither too deep into it. Snaking out your standpipe would be good too.
Rate me pl.....if helped.
Water inlet leaking
Take the hose off the valve and look inside it. There should be a flat rubber seal inside the hose coupling that seals to the valve. It sounds like you have lost this washer out of the end of the hose. You can pick them up at any hardware store. If they are over 5 years old, I suggest replacing the hoses completely anyway.
If this is not the problem, you may have cross threaded the hose on the valve. If this is the case you may have to change the valve.
Post back if you have any questions.
Mike
Very loud when spinning.....
the rear bearing is bad. its a sealed bearing and cant be regreased. it has to be replaced. very difficult job
12/13/2007 12:26:36 AM •
Frigidaire...
•
Answered
on Dec 13, 2007
No spin cycle
Get the plug off the wall, open up behind & check what it is. Maybe the belt is off...........Only severe cyclones are catastrophic........
No spin cycle
Did you check to see if there is a broken
belt present
Drum will not spin
If your water keeps flowing out, it could be that the pipe behind is not at the correct level, about three feet from ground level; your pump pumps the water out OVER this height. It should not be at ground level.
Frigidaire GLW51439FSO top load
have you had the back of the machine off if you know how to do this take back off and then try washing machine have a look to see if the belt is slipping on the drum could be that either the drum bearing has gone or that the motor has been overloaded and needs replacing also could just be the belt first of all i would take the back off and then try machine look where the belt goes from motor to the drum check if it is slipping if not slipping open the front door and try turning the drum by hand to see how much resistance there is on the motor shouldnt be to much after you have done this let me know the outcome and i will assist you further ok ill do all i can for you but remember i cant see what your seing so you need to explain in as much detail also other experts will see what you are saying and will also offer assistance but we need as much input from you as poss ok let me know
My Frigidaire GLTR1670A stops when it gets to rinse???
mchacon, start with the pump. Remove the lower panel and the pump will be on the right. Grab a pan and some towels and remove the hoses going to it. Clean out any coins, lent and whatever from the drain hose trap. Check the pumps impeller for lint, pins etc. This model has a pressure switch that will not advance the timer if it detects water in the tub. Also both fill valves must be on. You will not be able to see it under the basket. This picture is from another cat that had the same problem....Catriver..post back.
11/24/2007 10:06:19 PM •
Frigidaire...
•
Answered
on Nov 24, 2007
Door Locked and wont open
Mine is crazy too! Sometimes, if I open the soap dispenser it will open, othertimes not. Sometimes, if I pull up on the big, round knob (that you use to turn on the cycle), because it gets stuck down. Once in awhile, I just put it on the last 2 minutes of spin cycle again.
Actually it's Frigidaire CRTR9300ASO Help Please
Your pump doesn't have a pulley. With the washer full of water if your put it on the spin cycle will it pump out water? If so pump is probably ok and the pressure switch thinks the washer is full of water and spends the whole spin cycle trying to pump water out. If not then your pump is plugged or bad and needs to be replaced. If your dooe latch is bad your door lock light would not come on. So if it does come on in the spin cycle that part is probably fine.
Frigidaire affinity front loading washer
Any E20 code means your washer doesn't drain. More than likely there is a screw, nail, coin, bobby pin, etc locking up your pump and causing it not to drain. Keep in mind that your washer has a 1 yr warranty but some service companys will charge for this kind of repair because it is not technically covered under warranty.
Frigidaire Front Load Washer
most washer door seals when fitted correctly have drain holes at the bottom that allow water to drain from the rings as you call them, this may not be one of those seals and the problem is annoying but there really is no actual cure as such apart from wiping it out after each wash
to check if the door seal does have drain holes but is fitted wrong, look round the inner lip closest to the spinning drum to see if there are any holes, maybe higher up or near the top, if there are then it may be possible the seal was fitted wrong (if its not the factory original)
the cure then is to replace the door seal and fit correctly
some door seals have a large drain hole that is at the bottom that goes into the bottom of the drum (you can't see the pipe normally) this hole maybe blocked if thats the case try prodding it clear with something that wont damage the rubber (use common sense here)
hope i have been of some help
Err20
Hard to find what the ERR20 fault is. Sounds like something is stopping the pump. Are you using HE rated detergent? Sometimes you get a sud's lock on the pump, or something jamming or blocking the pump. If it wasnt HE detergent, it may have locked the pump down. Let me know how it turns out. Good Luck!!! Jim
'DR' indicator light on but door is shut
Check out your outlet drain filter; dr could be drain. Possible this is clogged or something or the water shd just drain. To reset press pause and reset together for about 4 seconds. Suggestions, ideas.
Frigidaire front loader
ACSEES TO THESE FRONT LOADERS MAKE IT HARD TO INSPECT COMPONETS. THERE MAY BE A CLUTCH ADJUSTMENT THAT IS NEEDED AND IS HARD TO ACCESS.
POSSIBLY JUST A LOSE MOUNT.
I WOULD CALL A "LICENSED FACTORY CERTIFIED REPAIR COMPANY" THAT WORKS ON YOUR "SPECIFIC MAKE AND MODEL". GOOD COMPANIES WILL HAVE A "FLAT-RATE DIAGNOSTIC FEE" TO FIND AND SOMETIMES IF IS A MINOR ADJUSTMENT, CHARGE LITTLE EXTRA OR NO CHARGE AT ALL OTHER THAN THE DIAGNOSTIC FEE.
MAKE SURE TO GET A WRITTEN ESTIMATE WITH THE "TOTAL COST" OF REPAIR BEFORE "SIGNING ANYTHING" OR LETTING THEM "START REPAIRS" IF THEY DONT INCLUDE IT IN THAT "DIAGNOSTIC FEE". !!!
Washer flashing fault codes
truthfully, i think you have a malfunctioning board.if all parameters are correct and unit is washing while beeping is taking place. represents board.
Metal noise under tumbler
You can try to locate the stuff by removing the bose right under your tub; of course by disconnecting all the wall electrics. Access to this is by removing the back panel.
Not finding what you are looking for?