20 Most Recent Frigidaire GLTF2940ES Front Load Washer - Page 7 Questions & Answers

Take the power plug off the wall. Be prepared for a lot of water before attempting the following: It doesn't spin because the unit is not draining water. It will not spin with water in it - must drain first. Check drain hose for kink,check exit pipe for blockage. Remove the front access panel, bottom front; if you find a pipe there with a cap -this is for draining water.Could be your "coin trap assembly" is blocked, therefore not allowing all the water to pump out. Remove the clamp that connects the trap assembly to the pump and clean it out. If helped, pl say so.

Hi,

I have the same problem with the E47 code. I had the service guy over and he brought a troubleshooting sheet. Basically, you must remove the door switch assembly and check the PTC (the white plug on the door switch assembly). According to the diagnostics sheet, if the switch is open or locked, then it is a doorswitch problem, but if the reading on the switch is ~ 1500 ohms, then its the control panel.

The reading on my PTC was ~ 1400 Ohms (which is close to 1500) so I ordered a new control board. I'll post again when it's re-installed.

See other posting

Hi Rana, I am happy to assist you! Generally, error code E11 means that your washing machine is taking a long time to fill (or is continuing to fill). Is the incoming water flow normal? If it is, does the fill water continue to enter your washer? If yes, disconnect power from your appliance. Did the water fill stop? If so, a service technician may need to check the pressure sensor or switch to determine if it needs replacement. If your water flow is abnormal, double-check water faucets to ensure they are in the "on" position. If on, your incoming water pressure may be above 30 PSI and could need adjusting. Check for any kinked or blocked water hoses or clogged water screens. If you've cleared the water screen and/or unblocked any kinked water hoses, and the problem still persists, it could possibly be a water inlet valve assembly. If you have checked all of the above, the unit may need a main control board replacement. I would recommend contacting a qualified service technician to further assist you in diagnosing this issue.

ugine washing machine error codes E11

Good Morning Kristy, thank you for your question! Because pedestals are designed specifically for the manufacturer brand appliances, I am unable to guarantee it is compatible for installation with a different brand as the dimensions and other specifications may vary. Best regards!

Have you got another washer? Because it might have been too old, or it has a bad quality when you have used it for ages. But if it's new, you could ask the people from the store you bought it from, and ask them about it as well.

Hello pkoehler, thank you for your inquiry! Often when the clothing continues to be wet in a washer, it is because the unit cannot properly drain and dispose of the water and detergent solution. Does the unit make a humming noise? If so, the drainage hose/pump may be clogged and needs to be cleaned. If not, the washer may possibly be experiencing an issue with the door lock assembly, faulty pump, timer or control board not communicating correctly. Because it could be a number of any one of several underlying causes, I would recommend contacting a professional to properly diagnose and repair the unit.

Pull the drawer out and find it with a paperclip.

Good Afternoon Rhonda, thank you for your post! "PAU" is in regards to the door does not securely latched or the cycle has been interrupted. Try pressing "PAUSE/CANCEL" or "START/PAUSE" once to resume washer. If proves to be ineffective, try reprogramming the appliance by unplugging it or flipping the household circuit breaker off. Wait approximately ten minutes and turn the unit on. If the issue persists, then the washer could possibly have a faulty door latch or experiencing a communication error with the control board. I would personally contact a professional to accurately diagnose the washer to determine the root cause to reduce the risk of unnecessary parts.

Hi Samuel, thank you for allowing me to assist you! Often when a unit does not spin, it is because the unit cannot properly drain and dispose of the water and detergent solution. Does the unit make a humming noise? If so, the drainage hose/pump may be clogged and needs to be cleaned. If not, the washer may possibly be experiencing an issue with the door lock assembly, faulty pump, timer or control board not communicating correctly. Because it could be a number of any one of several underlying causes, I would recommend contacting a professional to properly diagnose and repair the unit. Best regards!

the drain trap has to be cleaned out and the pump may also have something stuck in the impeller make sure those things are clean and you should be golden-it may only take one load to clog with the wrong kinda stuff getting into your machine-cheers Denny

you have blockage in the drain system-start with the drain trap-if that doesn't do it check the pump-which can get coins, bobby pins, and other stuff stuck in it-cheers Denny

circuit board problem replace it.

What is this on?