20 Most Recent
Frigidaire GLTF2940ES Front Load Washer - Page 6 Questions & Answers
Frigidaire GLTF2940ES3 Error code 41. Controls cycle on and off randomly.
Hello Scott, thank you for allowing me to assist you!
Based on the symptoms you are describing and if you are receiving an error code E41, your loading door may be ajar. Double-check to ensure that it is closed. If it is secure, reset the power again to your appliance for about ten minutes. If the error persists, it could either be the door switch assembly or the main control board in your appliance. In that case, a certified technician would generally replace the faulty part after proper diagnosis.
Best regards!
Washer fills then shuts off
Hi scottterriz, I am happy to assist you!
Often when your washer does not spin, it is because your appliance cannot properly drain and dispose of the water and detergent solution. Does your washer make a humming noise? If so, the drainage hose/pump may be clogged and needs to be cleaned. If not, your washer may possibly be experiencing an issue with the door lock assembly, faulty pump, timer or control board not communicating correctly. Because it could be a number of any one of several underlying causes, I would recommend contacting a professional to properly diagnose and repair your appliance.
Hope this helps!
Tell lid switch bad
Hello Kathleen, thank you for your post!
I understand that your washer will not spin; however is your appliance making a humming noise? If so, either the drain hose/pump is clogged and needs to be clean. Also try resetting your washer to the spin cycle only. Will water pump out? If it does not, then your washer could possibly have a faulty pump, timer, control board or door/lid lock assembly. In this regard, I would personally reach out to a professional for an accurate diagnosis and to assist with the repairs. You can often locate a qualified service provider by visiting the manufacturer website.
Cycle ends premature
Hello scotterriz, thank you for your post!
Based on the symptoms you are describing, you may either have a communication error from the main control board or the timer itself may not be operating correctly. If you noticed a humming noise, it could either be a clogged drainage hose or pump that needs to be cleaned, or it could possibly have another issue with the door lock assembly. Because it could be a number of any one of several underlying causes, I would recommend contacting a professional to properly diagnose and repair your appliance.
Best regards!
Won't spin out water
Good Morning Bernice, thank you for your post!
Often when your washer does not spin, it is because your appliance cannot properly drain and dispose of the water and detergent solution. Does your washer make a humming noise? If so, the drainage hose/pump may be clogged and needs to be cleaned. If not, your washer may possibly be experiencing an issue with the door lock assembly, faulty pump, timer or control board not communicating correctly. Because it could be a number of any one of several underlying causes, I would recommend contacting a professional to properly diagnose and repair your appliance.
Best regards!
How do you take the rubber seal off my frigidaire washer
Good Morning Laura, thank you for your post!
I understand your Frigidaire washer GLTF2940ES will not complete a cycle. Let's try resetting your washer. This can be done by either unplugging it or flipping the household circuit breaker to the off position. It is important to wait roughly ten minutes and then turn your appliance on.
If resetting the power does not correct the issue, then you may either have a communication error from the main control board or the timer itself may not be operating correctly. If you noticed a humming noise, it could either be a clogged drainage hose or pump that needs to be cleaned, or it could possibly have another issue with the door lock assembly. I would personally contact a professional to accurately diagnose the washer to determine the root cause to reduce the risk of unnecessary parts.
Best regards!
I go to start my
Hi
That is a door lock malfunction, check the lock and wire harness connections. Also turn the selector knob so the machine comes on then press the "options" and "select" buttons at the same time for 3 seconds.
Please get back to us if you have further query else please accept the suggestion.Thank you for contacting fixya.com
Washer does not fill
Widgett,
I understand that you are having trouble with water entering into your washer. Here are a couple of things to check out.
1) The water supply is possibly not adequate in the area where the washer is located. Check another faucet in the house. Wait until water supply and pressure increase.
2) The water supply faucets are not completely open. Fully open hot and cold faucets.
3) The water is being used elsewhere in the house. Water pressure must be at least 30 psi. Avoid running water elsewhere while washer is filling.
4) The water inlet hoses are kinked. Straighten hoses
If you are still having issues, I would suggest to contact a local authorized technician. When they come out they can take a look at the appliance up-close and determine what exactly is going on.
-Best Regards-
Backwards L code
Carol-Ann,
I have done some research on a "Backwards L" code for your washer, model# GLTF2940ES, through the manufacturers. There doesn't seem to be such a code for your appliance. It could possibly be that your display is segmenting or some of the LED lights are not showing fully. I would like to know what exactly the washer is or is not doing?
_Best Regards-
Not finding what you are looking for?