Frigidaire Gallery GLEFM397DS Electric Kitchen Range - Page 7 - Answered Questions & Fixed issues

Hi Junior- I found this youtube video on resetting f10 code on a gas stove. https://www.youtube.com/watch?v=z6tcnpDKDns Hope this helps.

if both arent working then you need to check your elements to make sure when one of them went out it didn't cause the other to go out. also, first check and make sure that they didn't come unplugged from the inside of the oven.

Dear IFE KIARA, Warning: If you feel in any way uncomfortable/unsafe performing this test or making this repair, please contact a qualified appliance repair technician. F13 error is related to the clock. this error can occur when the clock looses communication between the keypad or any of the sensor in the stove, including the heat probe. sometimes resetting the power will fix the problem. Try disconnecting power to the stove completely and flip the corresponding breaker on and off at the breaker box. Wait 30 seconds and then turn everything back on. if the problem persist after power-up, according to Frigidaire suggested corrective action the electronic oven control,also called EOC has to be replaced. Here is a search link from Google for the part in question. Best of Luck, JP https://www.google.com/search?source=hp&ei=fecFXYCMAsKr5wKBm6G4DQ&q=316418735&oq=&gs_l=psy-ab.1.0.35i39l10.0.0..5525...1.0..0.209.209.2-1......0......gws-wiz.....10.8VUU1xaL8qM

As copied from the manual. Setting a silent control panel When choosing a function, a beep will be heard each time a pad is pressed. If desired, the control can be programmed for silent operation. Press and hold (start/time) . After 7 seconds, the control will beep once. This will block the controls from sounding when a pad is pressed. To return the sound, press and hold (start/time) again for 7 seconds until the control beeps once NOTE! The OVEN indicator light on the electronic display will turn ON and OFF when using the Bake feature and during preheat. This is normal and indicates that the oven is cycling to maintain the selected baking temperature. When the preheat indicator light turns OFF, your oven is ready.

What is the model number?

Yes, the microwaves will still be contained,however it needs to be replaced. super glue will work if the original parts are broken or lost

The gas orifices for propane are different than LP gas. Are you trying to blow yourself up?

It is not based on time,. It uses temp sensors. When surface is cool enough it will go out..

This is going to require a new EOC, which is the control board. I attached a link that may help.

The first thing we want to do is disconnect all power to the range for 5 minutes. Turn the power back on and test. If that does not work it could be the induction generator or the relay board it would take some electrical testing to figure out which. I hope this was some help.

Code D81 is usually caused by a power surge of some type. The first thing to try is to unplug or shut off the power to the unit for 5 minutes and try it again.

That is a power fault. Your control board is bad.

Where is the office at to make the oven and smaller

1.Try disconnecting the electricity for 20 seconds, shut off the breaker in the breaker box to the oven. Then restoring it. 2.Try setting the oven into clean and starting it. Wait 30 seconds and cancel clean. Sometimes one of these methods work. Best to you

I suggest you lift off the burner ring and ensure there is no foreign matter in the area of the igniter. Observe whether the is a spark when you press the button to light the gas. It is possible that the ignition plug has failed, therefor you will need to purchse a replacement.

Shorted touchpad. Try unplugging for 5 minutes to see if it will reset

Here’s the link to Frigidaire answer center.

https://www.frigidaire.com/Owner-Center/Contact-Us/

just started 6 weeks ago and I've gotten 2 check for a total of $2,200...this is the best decision I made in a long time! "Thank you for giving me this extraordinary opportunity to make extra money from home. This extra cash has changed my life in so many ways, thank you!" Visit site:: SalaryHD­­.­­C­­o­­m

Check elements and all wiring connections

There are screens under front of top just above door. Remove those and top should lift up and remove