Top 20 Panasonic Viera TX-32LX70 32 in. LCD TV Questions & Answers

CHECK IN OTHER SOCKET OR BUY NEW TV

Well first I trust you removed the USB stick! I would say that some software clash occured and the best way I know would be to try and get to setup or initial set up and then use factory reset to restore its software to default. Should this fail then as a new set refer back to the seller for help as they have a duty to it for repair. As for that memory stick was it blank or have pictures on it? has it got a virus? or other software that may clash. In my view it should be formatted by the tv if it is for recordings or just carry images that your tv can support like say .jpg files other software programs could be a problem for it. Hope this helps........

Set-up (Programming) procedure is too much to type in here, and is not practical and it will differ brand-to-brand remote controls. If you wish to get more; check the sites linked here. The site has set-up code list & set-up procedure to many popular brand remote controls. The site has general set-up codes to check with TVs and other devices are given, in the order of the 'device's brand name list' in alphabetical order. Set-up code list to many brand remote controls also is given. Pull up older posts. Search the sites by type in the brand name to your device in its search box at the top right part of the display window. It will help you to find the document easily. http://remotesearch.blogspot.com/ http://electronicshelponline.blogspot.com/ http://electrohelponline.blogspot.com/ Programming Notes • If your device does not respond to the remote after trying all codes listed or your brand is not listed in the code list, use the Auto Code Search method to program your remote. • Sometimes the first code that "works" with your device may operate only a few functions of your device. There may be another code in the code list that performs more functions. Try other codes from the code list for more functionality. This is a trial and error procedure; and quiet time consuming. You might have to check different codes said for your device. Search the site by type in the "brand name" to your device; in the "Search box at the top right of the display window" to get gathered related posts.

HDMI is a signal what do you have going on here?

If you wish to get some details; check the site linked here. Pull up older posts. http://electronicshelponline.blogspot.com/

Set-up (Programming) procedure is too much to type in here, and is not practical and it will differ brand-to-brand remote controls. If you wish to get more; check the sites linked here. It has set-up code list & set-up procedure to many popular brand remote controls. One among it has general set-up codes to check with TVs and other devices are given, in the order of the 'device's brand name list' in alphabetical order. Pull up older posts. Search the sites by type in the brand name to your device in its search box at the top right part of the display window. It will help you to find the document easily. http://remotesearch.blogspot.com/ http://electro-medical.blogspot.com/ http://electronicshelponline.blogspot.com/ http://electrohelponline.blogspot.com/ Search the site by type in the brand name of your device, in the "Search box at the top right of the Home page display" to see the set-up codes to your device, with different brand remote controls.

Check and replace its tuner. If you wish to get some details; check the site linked here. Pull up older posts. Surf the site with patience. http://electronicshelponline.blogspot.com/

Fault to its main board. Short circuited component/s at it. Contact any service technician; or the authorized service center. If you wish to get some details; check the site linked here. Surf the site with patience. Pull up older posts. http://electronicshelponline.blogspot.com/ . In most cases, the main board might have to be replaced. If so, a software [firmware] update too might be necessary.

CALL YOUR CABLE PROVIDER

If you have another TV fed from the same antenna, I assume you have a splitter/distribution amplifier because you know you cannot just join two cables together don't you? It is more than likely the splitter/amplifier, cable or connections rather than the TV but to make sure you must move the TV in the other room and try it on the suspect cable before condemning the TV. Signal problems are usually due to water ingress and this could have happened on just one cable. Failing that, the TV input could have failed. It is not common but does happen now and then.

This has to do with the network & not your TV. For various reasons the networks may vary the overall time of programming, therefore you should schedule your recordings extending the record time.

this to allow some extra timing on the end to account for as to do with the timing of the program itself & not your TV. when recording a particular program it is a good idea to allot some time on the end to account for some stations overlapping.

CALL YOUR CABLE PROVIDER THEY WILL GUIDE YOU MR. ROBERTS

check the power supply circuit for leaky capacitors. You will recognize them by the bulging tops.

go to your source button on your tv remote then select HDI 1 or two if it is plugged into that one.

the easy way is just google your tv how to do this set up is found on you tube you google search your tv then free view re-tune on you tube then scroll down to it.

MYGOODFELLOW, YOU HAVE TO SWITCH FROM TV TO AV 1

In order to change the picture settings that affect picture size use the button on your remote marked aspect. If you want to change picture settings such as color, brightness, etc., use the menu button and select Picture, then hit Ok to enter that menu.

take it you have a dish for what in the uk is called sky ,go clean your dish of snow or ice on it.

press the menu button go to the settings there may be a option .